Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: sparky4lawndart

Page 1 of 27 1 2 3 4

Search: Search took 0.96 seconds.

  1. It's been a long while since I've posted here.....

    It's been a long while since I've posted here.. sorry...

    Wish me luck guys... I'm headed to Florida tonight for TopGun... Im guessing about 40 hours drive and I've got a club mate who's going to...
  2. Replies
    813
    Views
    56,903

    Just adding on to the band wagon here... I've...

    Just adding on to the band wagon here...

    I've just had the 5th cylinder failure (3rd on this motor) while in flight at a Scale Master event... Mid-throttle position, at least 4 minutes into the...
  3. Replies
    179
    Views
    31,744

    Looks great!!! happy holidays and awesome flying!

    Looks great!!! happy holidays and awesome flying!
  4. Replies
    1
    Views
    215

    SBUS RPM sensor

    Hello.. is there a Futaba SBUS RPM sensor that plugs into the gas engine Iginition module RPM output?
  5. Replies
    813
    Views
    56,903

    Hey guys.. I wanted your input on Fuel:oil mix......

    Hey guys.. I wanted your input on Fuel:oil mix... I've been running 17:1 Redline since I first got the motors (I have two)... any thoughts on running 30:1 with a synthetic like Amzoil (high...
  6. Replies
    4,236
    Views
    348,981

    Hi Zadeda, I think the paint and markings are...

    Hi Zadeda, I think the paint and markings are close but there's always a little artistic license!
  7. Replies
    813
    Views
    56,903

    It's been a long 4 day holiday flying weekend and...

    It's been a long 4 day holiday flying weekend and the motor let go a couple hours ago... I have probably 8 gallons of fuel through it and the same cylinder that broke last time broke again... at the...
  8. Replies
    813
    Views
    56,903

    Hey guys... still having a tough time getting my...

    Hey guys... still having a tough time getting my needles right... struggling with altitude changes at different sites, etc..

    I have my engine in a cowl that takes about 20 minutes to get off and...
  9. Replies
    4,236
    Views
    348,981

    Hey guys... my nearly 400 flight FW190 was killed...

    Hey guys... my nearly 400 flight FW190 was killed on the way back from the Warbirds over the Rockies event when the trailer came off the hitch at 70MPH. A toolbox started bouncing around and killed...
  10. Replies
    4,236
    Views
    348,981

    Ingenious... thanks for the great idea!

    Ingenious... thanks for the great idea!
  11. Replies
    239
    Views
    19,474

    a long time ago I called the BH Models...

    a long time ago I called the BH Models manufacturer in Vietnam begging for a couple spare kits... (the Wulf, this Macchi, and the SeaFury). After a long, difficult, discussion where English was an...
  12. Replies
    239
    Views
    19,474

    If it hasn't been mentioned yet.. there's a fix...

    If it hasn't been mentioned yet.. there's a fix you should do on the ailerons long hinge pin... if you lift the flaps you'll see a place to glue a small piece of thin ply or G10 to prevent that pin...
  13. Replies
    4,236
    Views
    348,981

    Is that a TIG or MIG weld?

    Is that a TIG or MIG weld?
  14. Replies
    813
    Views
    56,903

    replaced it.. It took a month but I'm okay with...

    replaced it.. It took a month but I'm okay with it...
  15. Replies
    813
    Views
    56,903

    It was sitting there patiently so I had to start...

    It was sitting there patiently so I had to start it up... couldn't run up the motor as the table wasn't strapped to anything and the propwash was blowing my hangar something fierce!!!

    ...
  16. Replies
    4,236
    Views
    348,981

    To add to the flames... I've had my TF GS FW190...

    To add to the flames... I've had my TF GS FW190 since they first shipped from Tower... It's got the same DLE55RA in it swinging a 22X10 Xoar normally and a 20X10 3Blade when necessary. I've had to...
  17. Replies
    383
    Views
    31,468

    Just asking.. I'm not asserting anything... ...

    Just asking.. I'm not asserting anything...

    with that much spacer on the axle don't you run the risk of a hard landing bending the axle and locking up a wheel? I've had a similar setup in a P51...
  18. Replies
    4,236
    Views
    348,981

    великолепные , поздравления

    великолепные , поздравления
  19. Replies
    4,236
    Views
    348,981

    awesome, JSZ!!!

    awesome, JSZ!!!
  20. Replies
    813
    Views
    56,903

    pretty spectacular... I went ahead and bought...

    pretty spectacular...

    I went ahead and bought another FG60R3 while Im waiting for the repair... this one starts on a couple flips with 6 out on the low and 5 out on the high.. Running really...
  21. Replies
    813
    Views
    56,903

    its off to Horizon.. fingers ...

    its off to Horizon.. fingers crossed!
  22. Replies
    813
    Views
    56,903

    answers... it was running great - it was...

    answers...

    it was running great - it was starting easily by hand... WOT @ 4,000 RPM with 2 out on the high needle and 6 out on the low needle (set with the throttle closed) very rich - a lot of...
  23. Replies
    813
    Views
    56,903

    20998412099842

    20998412099842
  24. Replies
    813
    Views
    56,903

    Here is the outcome today.. I got to the...

    Here is the outcome today..

    I got to the flightline early to meet a buddy of mine who's been doing this since the day of the dinosaurs, when dirt was clean, controlled flight meant you aimed the...
  25. Replies
    813
    Views
    56,903

    if I change the plug wires on 2 and 3 the motor...

    if I change the plug wires on 2 and 3 the motor tries to run.. if there where they're supposed to be the motor doesn't even pop...
    2099652
Results 1 to 25 of 672
Page 1 of 27 1 2 3 4
RCU Reviews
All times are GMT -6. The time now is 07:09 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.