Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: w8ye

Page 1 of 40 1 2 3 4

Search: Search took 1.02 seconds.

  1. Replies
    8
    Views
    250

    Use the SDC80 #

    Use the SDC80 #
  2. Replies
    1
    Views
    108

    Synthetic is fine to use for break-in as well as...

    Synthetic is fine to use for break-in as well as continued use
  3. Replies
    15
    Views
    577

    +1

    +1
  4. Replies
    15
    Views
    577

    If you cannot blow through the fuel inlet, the...

    If you cannot blow through the fuel inlet, the needle and seat of the metering valve is seated.

    Typically the arm resting on the diaphragm should be level with the surface where the...
  5. Thread: RPM too low?

    by w8ye
    Replies
    23
    Views
    706

    On gasoline the exhaust will be mostly dry smut....

    On gasoline the exhaust will be mostly dry smut.

    But what comes out the crankcase vent will look like diesel engine crankcase oil that has a 100,000 miles on it. It will be black syrup.

    You...
  6. Replies
    15
    Views
    577

    Tower and Horizon both operate a back order...

    Tower and Horizon both operate a back order business. To play their game - you had better get the parts you need on back order or you never will get them. For the parts are always on back order....
  7. Thread: RPM too low?

    by w8ye
    Replies
    23
    Views
    706

    The timing mark is sometimes a dimple and...

    The timing mark is sometimes a dimple and sometimes a line.

    If the timing is set correctly, there is a 50% chance that it is hidden behind the exhaust cam follower.
  8. Thread: RPM too low?

    by w8ye
    Replies
    23
    Views
    706

    The valves should both have .002" - .004"...

    The valves should both have .002" - .004" clearance.

    The mid point of the valve overlap event should be around 5 degrees before top dead center. Be sure you are turning the prop in the direction...
  9. Thread: Zenoah G38 Repair

    by w8ye
    Replies
    7
    Views
    376

    Its a good idea to replace the prop bolt with a...

    Its a good idea to replace the prop bolt with a stud, washer, & nut on the later G38's with the aluminum prop hub as the threads go pretty quick in the hub if you are always removing/replacing the...
  10. Thread: RPM too low?

    by w8ye
    Replies
    23
    Views
    706

    I would check the cam timing. My experience with...

    I would check the cam timing. My experience with the Magnum/ASP four strokes is that the cam is often set wrong.

    With the cam mark straight up or down, the engine will idle down - (tick like a...
  11. 2169650 This is what I use and like but the...

    2169650


    This is what I use and like but the 3" red insert is from Sullivan and not a blue Miller one.

    Runs 24V but has the same speed at the cone as a none geared Dynatron on 12V.
  12. I looked at the starters from Horizon, Tower, &...

    I looked at the starters from Horizon, Tower, & Sullivan and found the dimensions of the inserts and none were 2".
  13. http://www.terapeak.com/worth/toc-roto-terminator-...

    http://www.terapeak.com/worth/toc-roto-terminator-starter-rubber-cap-for-20-80cc-engine-od-52-id-40-h-30mm/262382191962/
    ...
  14. Replies
    2
    Views
    283

    You need to document the rpm when installed both...

    You need to document the rpm when installed both ways?

    I doubt it making a noticeable difference for when the reed valves are open, the piston is headed up and the intake charge is not going up...
  15. Replies
    7
    Views
    501

    I have a twin ring chainsaw with just the top...

    I have a twin ring chainsaw with just the top ring. Been that way a few years. Runs just fine.
  16. Replies
    13
    Views
    559

    I've used a lot of Caber rings and most of them...

    I've used a lot of Caber rings and most of them came from DLA. Never any problems.
  17. Replies
    8
    Views
    595

    Readjust the carb when you go to a different oil

    Readjust the carb when you go to a different oil
  18. Thread: snorkel tube

    by w8ye
    Replies
    2
    Views
    254

    I just run it back inside the fuselage behind the...

    I just run it back inside the fuselage behind the firewall area
  19. Replies
    125
    Views
    14,429

    Just call or Email Adrian Tel: (478) 247-7275...

    Just call or Email Adrian

    Tel: (478) 247-7275
    Email: adrian@ch-ignitions.com
  20. Thread: Bent G38 Cranks

    by w8ye
    Replies
    8
    Views
    477

    Cyberwolf does them too ...

    Cyberwolf does them too

    http://www.rcuniverse.com/community/profile.cfm?memid=86871
  21. The Evra was 31cc and that being so . . . they...

    The Evra was 31cc and that being so . . . they are probably talking about a 35cc Quadra

    But Quadras also came as 40's and later 42's then 50's etc

    Now days modelers use more power and the...
  22. Thread: Dle 30 cc

    by w8ye
    Replies
    23
    Views
    848

    They'll part throttle four stroke in flight...

    They'll part throttle four stroke in flight easier than they will on the ground
  23. Replies
    25
    Views
    1,536

    With mechanical advance you don't want to be...

    With mechanical advance you don't want to be turning it over with anything at full throttle and the ignition "ON"
  24. Replies
    3
    Views
    240

    The definitive prop for the G38 is the 18 X 10

    The definitive prop for the G38 is the 18 X 10
  25. Thread: hand starting

    by w8ye
    Replies
    34
    Views
    1,610

    This is what I use on the mag jobs

    This is what I use on the mag jobs
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
RCU Reviews
All times are GMT -6. The time now is 07:10 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.