Search: Posts Made By: laryboy
Showing results 1 to 25 of 500
Search took 15.15 seconds.
06-24-2018, 11:49 AM
Replies: 0
Views: 296
Posted By laryboy

instant throttle response

tactic 660. as I push the throttle forward the motor does not start rotating until the the throttle is at maybe 10 to 15 %. anything I can do to xmitter to get motor moving as soon as I push throttle...
07-26-2016, 02:17 PM
Replies: 174
Views: 30,987
Posted By laryboy

I am in.........larry

I am in.........larry
Forum: ARF or RTF
11-08-2015, 07:27 AM
Replies: 164
Views: 21,561
Posted By laryboy

problem will be with muffler installation. get...

problem will be with muffler installation. get pitts type......cut out opening in fuse. put muffler through hole and then
install motor
Forum: ARF or RTF
10-02-2014, 12:21 PM
Replies: 164
Views: 21,561
Posted By laryboy

any opinions on wheel size . pneumatic

any opinions on wheel size . pneumatic
Forum: ARF or RTF
09-02-2014, 01:12 PM
Replies: 164
Views: 21,561
Posted By laryboy

spinner

tell me about the spinner
05-29-2014, 04:45 PM
Replies: 1
Views: 360
Posted By laryboy

tactic 650

I want to use ch 5 for a" ignition off" module. I assigned a switch to switch the module from off to on.. the end points for the ch 5 are both set to 100%. What should they be set to ?
08-25-2013, 06:05 AM
Replies: 1
Views: 272
Posted By laryboy

compatibility

will my r617fs work with the ttx650 transmitter......................larry
Forum: Gas Engines
06-10-2013, 06:04 AM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

skip ......thank you ! engine used to run great with needles closed to normal position. i think you have pointed to the right track....................laryboy
Forum: Gas Engines
06-09-2013, 04:43 PM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

i have a jc 28 running lousy..tuned as normal but this time i found both needles open 2 turns rich. i tried a brand new carb but got same results. anybody got a theory ?
Forum: ARF or RTF
05-03-2013, 03:44 PM
Replies: 25
Views: 5,365
Posted By laryboy

RE: Ecomrc Stinson SR-9 from TBM

cant quite read the manual on this plane at troybuilt. can someone tell me how far from leading edge of wing is the balance point ? (frame 68).............................larry
Forum: Gas Engines
08-14-2012, 06:18 AM
Replies: 5,283
Views: 655,538
Posted By laryboy

RE: NEW DLE30!

what is the thread size on the 10 mm bolt......valley view single bolt adapter
Forum: Gas Engines
07-22-2012, 06:27 AM
Replies: 5,283
Views: 655,538
Posted By laryboy

RE: NEW DLE30!

swaping out my jc 28 for dle 30. mounting holes for jc 28 are 68 mm apart. holes for dle 30 are 70mm. do i really have to try to move holes (blind nuts) 1mm each ? larry
Forum: Gas Engines
07-19-2012, 06:04 AM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

me stupido ! pulled block apart...now i see the 4 metal flaps...thanks for your input...........larry
Forum: Gas Engines
07-19-2012, 05:37 AM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

i took apart my jc 28 to clean carb when i looked inside the reed block. i was expecting to see a little window with material screwed onto it to allow fuel and air in but not out. i didnt see...
Forum: ARF or RTF
06-08-2012, 06:43 PM
Replies: 25
Views: 5,365
Posted By laryboy

RE: Ecomrc Stinson SR-9 from TBM

no comment on ill fitting cowl ?
Forum: Gas Engines
02-14-2012, 05:55 PM
Replies: 2,427
Views: 231,855
Posted By laryboy

Forum: Gas Engines
02-14-2012, 05:53 PM
Replies: 2,427
Views: 231,855
Posted By laryboy

Forum: Gas Engines
02-14-2012, 02:03 PM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

thank you very much...i will get a gasket with no holes
Forum: Gas Engines
02-14-2012, 01:50 PM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

the replacement gasket has the 2 holes in it. is it usable ?
Forum: Gas Engines
02-14-2012, 01:13 PM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

it is the same size as the opening in the carb. engine ran ok. i noticed 2 small holes in reed block, but no holes in gasket. replacement gasket has 2 holes that match reed block.....do i need a...
Forum: Gas Engines
02-14-2012, 12:29 PM
Replies: 2,427
Views: 231,855
Posted By laryboy

RE: RCAero JC Engines & YDA Engines

i took the walbro off my jc 28 and i looked at the carb mounting gasket , still attached to reed block (that black thing). the diameter of the large hole in the gasket was smaller than the opening in...
Forum: Gas Engines
01-25-2012, 04:51 PM
Replies: 51
Views: 3,278
Posted By laryboy

RE: WT 813 Syssa Carb Won't Pop

W8YE....per your advice a time ago i replaced a faulty wt-805 with a much cheaper wt-664 and every thing worked perfectly. now if i am reading this thread correctly, a wt -76 (which is real cheap)...
Forum: Gas Engines
11-22-2011, 10:05 AM
Replies: 6,835
Views: 711,021
Posted By laryboy

Forum: Gas Engines
06-27-2011, 01:38 PM
Replies: 6,835
Views: 711,021
Posted By laryboy

RE: RCGF Engines

yes i have one .........laryboy@comcast.net........
06-25-2011, 11:22 AM
Replies: 13
Views: 3,560
Posted By laryboy

RE: Boeing F4B Plans

does anyone have the john tanzer plans of the f4b or the completed model? i need the balance point. balsa products f4b was the john tanzer design.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service