Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: rcairboater

Page 1 of 10 1 2 3 4

Search: Search took 1.83 seconds.

  1. Replies
    23
    Views
    428

    That looks just about the shape mine is in. What...

    That looks just about the shape mine is in. What are you planning for this engine?
  2. Replies
    23
    Views
    428

    Could I use a piston from another engine? If so...

    Could I use a piston from another engine? If so What type of engine and how do I measure if needed?
  3. Replies
    23
    Views
    428

    Interested in selling the engine?

    Interested in selling the engine?
  4. Replies
    23
    Views
    428

    I need to stay in the 25 to 30 cc range for the...

    I need to stay in the 25 to 30 cc range for the hull I built. I would really like to get this engine going to put on the hull. After all, I did purchase this engine here on rcu from a well know...
  5. Replies
    23
    Views
    428

    So this engine is not worth the time or effort to...

    So this engine is not worth the time or effort to get to run? Can anyone help with part's for this engine?
  6. Replies
    23
    Views
    428

    Thanks, What are your thoughts on the intake and...

    Thanks, What are your thoughts on the intake and exhaust timing for this engine?
  7. Replies
    23
    Views
    428

    I looked at the back plate and not much room for...

    I looked at the back plate and not much room for stuffing the crankcase. Any other ways of increasing compression? Leaving off the jug/block gasket to achieve .020
  8. Replies
    23
    Views
    428

    Thanks. Their is a nick in the top of the piston...

    Thanks. Their is a nick in the top of the piston with a piece of the piston sticking up slightly. Can this be repaired or is the piston junk? Sanded flush?
  9. Replies
    23
    Views
    428

    Sand the bore up and down like the piston would...

    Sand the bore up and down like the piston would travel? What solvent? Anything with the piston?
  10. Replies
    23
    Views
    428

    So I have a 11mm carb, Would this engine be a...

    So I have a 11mm carb, Would this engine be a good for this carb? What can I do to get this engine a good runner?
  11. Replies
    23
    Views
    428

    Engine information

    Anyone know what engine this is and what are your thoughts on the condition? I believe it to be a 30cc Homelite. The rings are pinned so I will get a bowman ring. Do I need to get two rings or just...
  12. Replies
    3
    Views
    114

    31" by 18"

    31" by 18"
  13. Replies
    36
    Views
    874

    Do you have any additional information on the...

    Do you have any additional information on the hull that you posted?
  14. Sticky: Few additional questions. What type sand paper...

    Few additional questions. What type sand paper and grit do we use to remove the squish band? Size of Pvc tube? Second, when do you record the exhaust, intake timing, soon as we see the light through...
  15. Sticky: Anyone? Do I chuck a pin vise in my drill press?

    Anyone? Do I chuck a pin vise in my drill press?
  16. Sticky: When drilling the piston when doing a bowman ring...

    When drilling the piston when doing a bowman ring what do we need to do so the drill bit doesn't "walk" in the piston land?
  17. Sticky: When finding a used engine what compression is...

    When finding a used engine what compression is considered good and what tool do you recommend we us to check? (homelite).
  18. Sticky: What do you recommend we use for a V block?

    What do you recommend we use for a V block?
  19. Sticky: Thanks for the explanation, What do we use to...

    Thanks for the explanation, What do we use to grind down the pin once it's in the the piston? Type of bit/disc? Also, what procedure is used to install the Bowman ring?
    Thanks.
  20. Sticky: How deep do we drill in the piston land? Any...

    How deep do we drill in the piston land? Any pic's you care to share? Size of gas welding rod and drill bit?
  21. Replies
    3
    Views
    92

    What size gas rod and size type drill bit?

    What size gas rod and size type drill bit?
  22. Replies
    3
    Views
    92

    Pinning a piston

    I want to add a Frank Bowman ring to my 25cc Homelite engine. Anyone care to explain how to do this and what tools are needed?
    Thanks.
  23. Replies
    7
    Views
    757

    The skeg on the bottom of the boat is used with...

    The skeg on the bottom of the boat is used with the steering. The boat being flat bottom, has the skeg there to provide opposition to the rudder. If the skeg wasn't there the rudder would act like a...
  24. Thanks for the pics. What exact engine mods did...

    Thanks for the pics. What exact engine mods did you do with the conversion? Intake, exhaust, compression?
  25. If you have the time, that would be good. What...

    If you have the time, that would be good. What size round bar did you use on the rigging? Is this the engine you are speaking of?
Results 1 to 25 of 248
Page 1 of 10 1 2 3 4
All times are GMT -6. The time now is 02:03 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.