Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: breadmantripp

Page 1 of 2 1 2

Search: Search took 0.05 seconds.

  1. Replies
    2
    Views
    249

    So I think I found out what the problem was. I...

    So I think I found out what the problem was. I bought it off eBay. I didn't put much thought into the fact that it was new but had been taken apart from a new engine. Anyway when they took it apart I...
  2. Replies
    2
    Views
    249

    3 shoe clutch problems

    I've recently upgraded my engine on my buggy and it came with a 3 shoe clutch in which I've never delt w/ one before. Every clutch before for this has had a 2 shoe w/ a spring. Anyway I am trying to...
  3. Replies
    3
    Views
    402

    U can prob lean ur high speed needle if u want,...

    U can prob lean ur high speed needle if u want, but there is nothing wrong with those temps. It's not until 260/270 degrees that u need to start 2 worry.
  4. Replies
    2
    Views
    169

    And it's a Sullivan tiger drive not tigerstart,...

    And it's a Sullivan tiger drive not tigerstart, if I happened to confuse
  5. Replies
    2
    Views
    169

    Any1 at all?

    Any1 at all?
  6. Replies
    2
    Views
    169

    Tigerstart

    Has any1 installed a tigerstart on their backdraft or earthquake 3.5, and if so what tigerstart model (s680, s690, ect.) did u use?
  7. Replies
    8
    Views
    389

    Guff plz keep us informed on how ur backdraft is...

    Guff plz keep us informed on how ur backdraft is doing. Personally I would tell u to stay away from redcat or at least the backdraft cause I own 1 and am constantly fixing some kinda problem. Mainly...
  8. Buy something other than redcat.

    Buy something other than redcat.
  9. Replies
    4
    Views
    293

    That's a lot of servo's

    That's a lot of servo's
  10. Replies
    4
    Views
    293

    Planning on installing single steering servo.

    Planning on installing single steering servo.
  11. Traxxas clutch will wrk. Put 1 on mine

    Traxxas clutch will wrk. Put 1 on mine
  12. Replies
    4
    Views
    293

    Servo suggestions

    Jus wanna get ppl's input on some quality servo's. Lookin to upgrade mine on my revo3.3
  13. Replies
    5
    Views
    581

    Would only sh sleeves and pistons fit their...

    Would only sh sleeves and pistons fit their engines or could there b others that would fit also?
  14. Replies
    5
    Views
    581

    Bummer

    Bummer
  15. Replies
    5
    Views
    581

    .21 engine question

    I need to replace my sleeve and piston in my sh .21 engine and am wondering if any sleeve and piston will work as long as it's for a .21 engine?
  16. Replies
    1
    Views
    285

    Engine probs

    I can get the engine 2 start but only after the fuel has sat in engine for lets say 10 min. Once I get it to start it seems as if the idle is very high and once I apply full throttle it cuts out and...
  17. Replies
    3
    Views
    167

    Already did it, that wasn't the problem

    Already did it, that wasn't the problem
  18. Replies
    3
    Views
    167

    Wheel stops spinning

    On my 1/36 losi micro t I pull in on the throttle with the wheels off the ground both tires start spinning but one eventually stops spinning while other keeps goin. Anybody have any clue what goin on...
  19. Replies
    7
    Views
    409

    Done it. We start very loose, then tighten till...

    Done it. We start very loose, then tighten till it till we finally have the right amount of slip. The motor mount is pushed all the way over or it won't mesh properly, I'll have 2 post some pics or...
  20. Replies
    7
    Views
    409

    Seriously, I about can't take it anymore. Went...

    Seriously, I about can't take it anymore. Went back 2 the metal spur gear but started chipping the bell, which is why I quit using the metal, but my plastic spur gears last about 5 times around the...
  21. Replies
    7
    Views
    409

    Now it's my spur gear, keep stripping the gear. I...

    Now it's my spur gear, keep stripping the gear. I kno the mesh is fine. Can't fig out why this keeps happening? I bash my traxxas jus as much mayb even more, and no probs this yr. I just can't figure...
  22. Replies
    3
    Views
    510

    Should I throw it away?

    I'm guessing most of u will say yes but here it goes anyway. I bought a redcat backdraft 3.5 last yr cuz I wanted my dad 2 get n2 rc with me. I was new 2 the hobby and just wanted 2 get the least...
  23. Replies
    7
    Views
    409

    I need better parts

    Keep stripping thread on servo saver on my backdraft 3.5, need 2 kno if any1 has used another company's servo saver? Or if any of the hop up parts for other redcat cars will work on the backdraft...
  24. I did loosen them already, but it was that nut on...

    I did loosen them already, but it was that nut on top of the left post of the servo saver. I had 2 tighten it. I basically rebuilt the car due 2 the chasis was bent. I had purchased the upgraded...
  25. I'm thinking it has something 2 do w/ the servo...

    I'm thinking it has something 2 do w/ the servo saver. Mayb the bolt that screws into the top of one of the posts on the saver? I'm messing around w/ it right now but nothing has seemed to work yet
Results 1 to 25 of 30
Page 1 of 2 1 2
RCU Reviews
All times are GMT -6. The time now is 10:49 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.