Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Randy M.

Page 1 of 40 1 2 3 4

Search: Search took 1.78 seconds.

  1. I was told in was number 2;)

    I was told in was number 2;)
  2. Replies
    34
    Views
    1,924

    It is a beast! Hank's 22 was rocking!

    It is a beast! Hank's 22 was rocking!
  3. Scott, Betsy and I are heading there now for the...

    Scott, Betsy and I are heading there now for the day. Will return later in the week for more jet flying action.
  4. Replies
    34
    Views
    1,924

    My friend has 002. Will be flying it at JOKE next...

    My friend has 002. Will be flying it at JOKE next week. We ran it last week and what a beast it is. Can't wait to see it go.
  5. Very sorry to hear. Praying for a speedy recovery.

    Very sorry to hear. Praying for a speedy recovery.
  6. Replies
    25
    Views
    1,735

    Go to local hvac supply house and match it up. It...

    Go to local hvac supply house and match it up. It may be a little hard to find as they're pretty old. And there's always Google.
  7. Replies
    25
    Views
    1,735

    Yup that should do it.

    Yup that should do it.
  8. Replies
    7
    Views
    287

    Amt Netherlands. Or if you know a good...

    Amt Netherlands. Or if you know a good machinist, or you are one, diy. Pull the intake, make some s tandoffs. Mount the starter motor. You might need another compressor nut also. Or machine the...
  9. Replies
    41
    Views
    1,611

    For balancing you could try a local turbo...

    For balancing you could try a local turbo rebuilding shop. We have one here that was helpful on an old motor I was playing around with.
  10. Replies
    6
    Views
    304

    I have a set from Shepp. They work great in my...

    I have a set from Shepp. They work great in my turbinator.
  11. The garage is my work space. My wife's car has...

    The garage is my work space. My wife's car has never been in there. That's the key. Once they get the car in there, they will never park outside again. Also my garage has low ceiling. So no lift for...
  12. I mounted mine in front of the main tank. I cut a...

    I mounted mine in front of the main tank. I cut a hole in the equipment board and made a mount to hold it in place. Mine is the arf
  13. I have a two car garage. The area between the...

    I have a two car garage. The area between the two doors I built a rack. It's a 2x4 frame with a heavy base. I put heavy duty adjustable track on both sides. I use the heavy shelf brackets lined with...
  14. I was actually considering the same thing...

    I was actually considering the same thing recently. I was thinking on getting the wiring harness and pump. simply unplugging the ecu and engine. Fuel system would be close to identical in each...
  15. Likely one more!

    Likely one more!
  16. Replies
    25
    Views
    1,152

    I had a similar issue with my turbinator. The...

    I had a similar issue with my turbinator. The tank is long and sits flat like the flash. I changed my clunk setup completely. I took a large Dubro clunk, I cut the barb off flush. I then bored the...
  17. Replies
    222
    Views
    42,733

    only available from dreamworks

    only available from dreamworks
  18. Replies
    14
    Views
    698

    Looks like a lot of the hard stuff is done. I...

    Looks like a lot of the hard stuff is done. I just finished the flaps and ailerons on mine. Will you be using the single intake? You may not be able to get it in now though. I think the 140 will...
  19. Replies
    12
    Views
    438

    P 80, p 100, k80, k 100. Lots of good choices....

    P 80, p 100, k80, k 100. Lots of good choices. I'm a little partial to the k100. Great power, easy install , and great price.
  20. Replies
    125
    Views
    11,907

    The inner holes for the flap hinges are pretty...

    The inner holes for the flap hinges are pretty close to the spar. The first is about 1/2" or so and the gradually get deeper. You just drill to the spar and cut the hinges down a bit.
  21. Replies
    125
    Views
    11,907

    I'm building one now for single amt 450. Mine is...

    I'm building one now for single amt 450. Mine is the old polyester df version. I bought the new formers from yellow. They look to be up to the task. I will use the stock wing set with some mod work...
  22. Replies
    21
    Views
    666

    I have a friend that has a vacuum form machine....

    I have a friend that has a vacuum form machine. He made a plug for his small futura wing tips and they also fit my L-39 top tanks.
    he may be persuaded to pull a couple if you don't find a solution.
  23. Replies
    44
    Views
    2,974

    A Tam pipe is a must if it's a single. I put the...

    A Tam pipe is a must if it's a single. I put the fej pipe in at first and did some engine runs and taxi tests. When I put the Tam pipe in it was noticeably cooler and had more power.
    I also had the...
  24. Replies
    44
    Views
    2,974

    It's my belief that after I added flaps and the...

    It's my belief that after I added flaps and the nose pitched down, the elevators fluttered. I think the flaps just disrupted the airflow enough to cause it. The biggest problems fej has had has been...
  25. Replies
    44
    Views
    2,974

    If you watch the video, draw a line straight down...

    If you watch the video, draw a line straight down from the last frame. Not really a landing though.
    I may post it soon. It has been a year now. Working on it replacement. A yellow aircraft kit. Old...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 12:45 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.