Search: Posts Made By: r degen
Showing results 1 to 25 of 165
Search took 0.89 seconds.
02-24-2008, 07:52 PM
Replies: 4
Views: 859
Posted By r degen

b-24 liberator

I need the manual how to build the jack stafford b-24 that you can have websit to print them off?
Forum: RC Jets
12-13-2006, 08:48 PM
Replies: 19
Views: 3,487
Posted By r degen

RE: backpack fire extinguisher

They are called Indian Fire pump. Randy
http://www.edarley.com/edarley4/finditem.cfm?itemid=11195
Forum: RC Jets
08-30-2006, 04:39 PM
Replies: 11
Views: 1,157
Posted By r degen

RE: Maverick opinions DF or turbine

ecoliburger

I have a BVM 91 in mine The wing tip tanks will knock about 10mph off the speed but they do make it show up a lot better
in the air. I Have never noticed that much differance...
Forum: RC Jets
08-02-2006, 03:51 PM
Replies: 33
Views: 3,009
Posted By r degen

RE: Ghostrider down

HEY Ben Hope you get well soon The Big Chicken
Forum: RC Jets
05-31-2006, 08:49 PM
Replies: 1
Views: 648
Posted By r degen

BVM aluminum nose retract ??

Can a BVM 90° rotating aluminum nose retract # 5375 be changed to a non-rotating retract Thanks Randy
05-04-2006, 09:50 PM
Replies: 70
Views: 11,720
Posted By r degen

RE: Outfitting my box trailer.

How big fire extingisher (dia.)will the Pit Pal hold . Nice trailer Thanks Randy
11-17-2005, 09:18 PM
Replies: 27
Views: 6,176
Posted By r degen

RE: Cutting slots in plywood

I would use a router table with a fence I think you can get high speed steel bits from sears or use an 1/8 inch end mill. Randy
11-08-2005, 12:32 PM
Replies: 37
Views: 16,042
Posted By r degen

RE: Removing chuck from drill press?

desmobob


There is usually a slot in the quill that you can put a drift punch in and knock it out. Randy
Forum: The Clubhouse
10-06-2005, 04:48 PM
Replies: 85
Views: 5,782
Posted By r degen

RE: What's your club's web page?

www.larksclub.homestead.com
10-03-2005, 08:55 PM
Replies: 12
Views: 2,597
Posted By r degen

RE: Making up foam wing balsa sheeting

Mike

I to use polyurethane glue Tightbond I have built one 35% extra that I have been flying for three years now. The poly is great glue it comes through the wood grains and the sheeting is...
Replies: 4
Views: 678
Posted By r degen

RE: Antenna tubes-inside plane.....

It is not a problem I 'am using them in my 35% extra with a DA 100
Forum: RC Jets
09-13-2005, 08:11 PM
Replies: 4,459
Views: 718,865
Posted By r degen

RE: Reaction 54 Jet Kit

afterburner that is what I had in mind is the manual on line somewhere I need the list of servos Thanks
Forum: RC Jets
09-13-2005, 04:03 PM
Replies: 4,459
Views: 718,865
Posted By r degen

RE: Reaction 54 Jet Kit

Hey Guys what servos are you using in your Reactions ?? can you list them Thanks Randy
Forum: RC Jets
09-09-2005, 03:56 PM
Replies: 1
Views: 611
Posted By r degen

RE: BVM Maverick help

Yes You do have to cut into the foam to clear the retracts . Randy
Forum: RC Jets
07-31-2005, 10:08 PM
Replies: 2
Views: 651
Posted By r degen

Retract problem in a Bobcat

I just started flying my bobcat and the nose retract starts to go up when you retract them and then comes right back down . The mains are working fine . I am using a robart vr control Valve
This...
Forum: RC Jets
06-12-2005, 08:19 AM
Replies: 29
Views: 10,301
Posted By r degen

RE: JetCat P60 Oring Replacement DIY

Hey Dave how many starts did you have on your P-60 before you replaced the o-ring? Thanks Randy
04-03-2005, 08:00 AM
Replies: 7
Views: 685
Posted By r degen

RE: Number of servos run thru Receiver?

Chuck I am using 8 Hitec digitals on my 35% extra on one 9 channel receiver , two 6volt 1700ma nicads and two separate switches and have never had a problem. Randy
Forum: The Clubhouse
03-26-2005, 09:57 PM
Replies: 24
Views: 1,480
Posted By r degen

RE: Who's going to Toledo?

Steve you don't have to wait outside you can go in and buy your ticket for the show then go up to the swap shop. Randy
02-14-2005, 09:57 PM
Replies: 10
Views: 653
Posted By r degen

RE: Glueing Ply to fiberglass

Just make sure you sand it good with 80 grit no matter what you use for glue . I would use aeropoxy ,hysol, or epoxy .Randy
Forum: The Clubhouse
02-07-2005, 04:45 PM
Replies: 2
Views: 414
Posted By r degen

RE: Tru-Turn spinner backplate

Randy I have a 4-1 /2 tru turn on my Hurley Extra the back plate is flush to the drive plate .
I also have a smaller on it is flush to . Randy
Forum: The Clubhouse
02-03-2005, 10:19 PM
Replies: 2
Views: 954
Posted By r degen

RE: Bill Hemple videos?

Here's the link your looking for Pat http://www.rcuniverse.com/magazine/billhempelwildonethree.cfm

Randy
Forum: RC Jets
01-29-2005, 12:06 PM
Replies: 10
Views: 918
Posted By r degen

RE: LOOKING FOR ROOKIE VIDEOS

Yep it sure was you Ben but I can't take credit for the video it was another club member. Randy
Forum: RC Jets
01-28-2005, 07:35 PM
Replies: 10
Views: 918
Posted By r degen

RE: LOOKING FOR ROOKIE VIDEOS

Nighthawk117 Take a look at this link. This Rookie has a jetcat p-120 . Randy
http://www.larksclub.homestead.com/flywhatyoubring.html
Replies: 3
Views: 490
Posted By r degen

Hitec programmer ??

Why does the battery in my Hitec Programmer go dead after sitting not in use for a week or to .Thanks Randy
Forum: RC Jets
01-22-2005, 09:05 AM
Replies: 31
Views: 1,912
Posted By r degen

RE: Roo speed brake ??

Hey Thanks for all the info Guys Randy
Showing results 1 to 25 of 165
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service