Notices
Search: Posts Made By: jiminy
Showing results 1 to 19 of 19
Search took 0.69 seconds.
Forum: RC Jets
11-21-2011, 06:28 AM
Replies: 1
Views: 422
Posted By jiminy

Looking for an Avonds or Tams F15 dual exhaust pipe

Hi All,
Anyone out there got a dual exhaust (split) tailpipe for a Phil Avonds F15 they are not using and wish to sell? I have decided to finally build my F15!! Yay! Of course if you have any...
Forum: RC Jets
05-20-2004, 01:20 PM
Replies: 18
Views: 2,314
Posted By jiminy

Any New Jet Kits coming this year?

Anyone know of any new jet kits being released this year? Don't feel like buying anything if something better is coming soon.. wasn't BVM going to be coming up with something new ? Seems like an...
01-06-2003, 02:19 AM
Replies: 13
Views: 2,149
Posted By jiminy

ace2002.. question for you

Mike, (ace2002)
What causes the polyester gel coat to wrinkle? Can you tell me what the preferred conditions are to use this for coating the plug?
The reason I ask is that this happened to me and...
01-06-2003, 02:09 AM
Replies: 0
Views: 412
Posted By jiminy

plane questions

Hi guys,
can anyone tell me which planes I can use (download?) to simulate the following:

Prather Lil Toni .40 pylon racer
Bob Violet Bandit (turbine and ducted fan)

As always, your...
11-28-2002, 03:20 PM
Replies: 53
Views: 8,350
Posted By jiminy

Go Visit a Lanc near You!

Hi,
I think there is a Lancaster (full size) at Nanton Alberta that you could take a close look at.. you may want to check into it.

regards, Jim
11-03-2002, 12:44 AM
Replies: 3
Views: 656
Posted By jiminy

getting cross sections from fullsize

Hi Guys,
anyone out there have an easy way of taking fuselage contours off a full size plane?
I have access to the real thing but am wondering how to go about it.. someone MUST have done this...
10-29-2002, 09:53 PM
Replies: 4
Views: 1,124
Posted By jiminy

F5-E plan information wanted

I am looking to build a scale Northrop F5-E model and was wondering if anyone could point me in the direction of a good set of drawings for this aircraft along with fuselage cross sections.. yeah I...
10-16-2002, 01:44 PM
Replies: 5
Views: 1,045
Posted By jiminy

further info..

I forgot to mention that the battery was low when I first powered up the Tx.. but it WAS working before I did the charging thing.

thanks, Jim
10-16-2002, 01:41 PM
Replies: 5
Views: 1,045
Posted By jiminy

Dead JR display on a 347 Tx

Hi Danny,
I have a heli x347 that has been very lightly used. The tx has been sitting since last year. I decided to charge it up and cycle by leaving the tx on and charging again. I used the stock...
Replies: 1
Views: 659
Posted By jiminy

JR Transmitter display dead

Hi,
I have a JR x347 transmitter that I charged after sitting a while, then I left the TX on to discharge. Then I charged fully (going by time). After this I went to switch on - and the display...
Forum: RC Jets
08-13-2002, 08:10 PM
Replies: 2
Views: 527
Posted By jiminy

BVM Viper Servos

Hi Guys,
anyone out there who can recommend the number and model of JR servos to fully outfit a BVM Viper with all options ?
I am looking to buy the servos together (and hopefully get a good...
Forum: RC Jets
07-31-2002, 06:17 PM
Replies: 1
Views: 430
Posted By jiminy

Aggressor plan ripped - help!

The dog ate my jet plan!... .

I am in dire need of BVM Aggressor tail and nose gear plan section.. it is the top and middle right corner of plan sheet.. I have the rest of the plans but am...
Forum: RC Jets
07-11-2002, 01:38 PM
Replies: 4
Views: 710
Posted By jiminy

Viper Conversion - Help!

Hi Guys,
I am currently building a BVM Viper which I have lying around. It has a ducted fan setup.. no tailpipe has been installed yet..,
Engine will be a KBV82.

I would like to leave my...
Forum: RC Jets
07-10-2002, 02:20 PM
Replies: 4
Views: 602
Posted By jiminy

Viper Question

Hi All!

Does anyone know whether BVM Viper wings have a "sawtooth" notch in the leading edge.. I have a set that are already covered and was wondering if they were custom made or came like that...
Forum: RC Jets
05-14-2002, 02:48 PM
Replies: 3
Views: 596
Posted By jiminy

Sorry- didn't read your note fully!

Sorry.. are you looking for the plan only.. I think I may have that also.. let me know

regards, Jim
Forum: RC Jets
05-14-2002, 02:46 PM
Replies: 3
Views: 596
Posted By jiminy

BAE Hawk

There is an excellent building video that goes with the plan.. I highly recommend it.. I have an original tape and can sell it to you for $20 + shipping if you can't find it at RCME.

regards, Jim
05-10-2002, 07:19 PM
Replies: 0
Views: 469
Posted By jiminy

wanted G2 JR interface cable

Hi All!
Anyone out there got a JR TX interface for G2 they don't need? If so, please let me know..

thanks, Jim
Forum: RC Jets
05-09-2002, 05:49 PM
Replies: 3
Views: 577
Posted By jiminy

F5E kits???

Okay guys,
who can tell me who is making or planning to make a large scale F5E kit for turbines?

Jim
Forum: RC Jets
04-30-2002, 12:16 PM
Replies: 1
Views: 394
Posted By jiminy

Bay Of Quinte Jet Rally

Hi Guys!
Anyone out there know the date for this years jet rally in Ontario Canada? Is there a website for this?

thanks, Jim
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.