RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: dnimigon
Showing results 1 to 18 of 18
Search took 0.25 seconds.
Forum: Gas Engines
06-11-2023, 02:18 PM
Replies: 26
Views: 2,628
Posted By dnimigon

Who is this Ralph your talking about. Does he...

Who is this Ralph your talking about. Does he have a website
Forum: Gas Engines
06-11-2023, 02:09 PM
Replies: 13
Views: 11,503
Posted By dnimigon

GT80 with no spark.

I think I might have a couple bad coils on this engine. I'm getting no spark. What is the best way to check these coils. Should I be getting some kind of an ohm reading or a dead short between the...
Forum: Marketplace
06-26-2018, 05:27 PM
Replies: 3
Views: 1,857
Posted By dnimigon

Reply

PM sent to you
Forum: Giant Scale Aircraft - General
05-17-2018, 06:20 PM
Replies: 2
Views: 846
Posted By dnimigon

Cowl attaching

Building a Ziroli Spitfire and Been test fitting cowl to figure out engine placement. Been wondering how you guys attach the cowl that looks scale. Can't have big screws showing. Just wondered how...
Forum: Marketplace
05-09-2018, 08:16 AM
Replies: 5
Views: 899
Posted By dnimigon

Let me know if it falls through

Let me know if it falls through
Forum: Marketplace
05-08-2018, 05:09 PM
Replies: 5
Views: 899
Posted By dnimigon

Is this still for sale

Is this still for sale
Forum: Marketplace
05-07-2018, 06:29 PM
Replies: 1
Views: 438
Posted By dnimigon

Do you still have the G-38. You say you didn't...

Do you still have the G-38. You say you didn't run it. ??????
Just wondering why .
Forum: Marketplace
05-06-2018, 04:54 PM
Replies: 7
Views: 568
Posted By dnimigon

Yes, everything looks good. I'm going to pass on...

Yes, everything looks good. I'm going to pass on this at this time. I have to think on shipping and exchange rate. Would put me up to around $1000 CDN I'm sure. Appreciate your time and courtesy. ...
Forum: Marketplace
05-04-2018, 05:55 PM
Replies: 3
Views: 410
Posted By dnimigon

What kind of dollar would you be after. Also...

What kind of dollar would you be after. Also where are you located. I'm in Canada so have to consider the exchange rate on US prices.
Dave
Forum: Marketplace
05-04-2018, 05:53 PM
Replies: 7
Views: 568
Posted By dnimigon

Your location

Are you located in Canada?? I googled the husky as I couldn't remember what the Husky was about. Saw your add talking about hipping to US from Canada. I'm in Albert here. Just west of Edmonton.
Dave
Forum: Marketplace
05-03-2018, 05:53 PM
Replies: 3
Views: 410
Posted By dnimigon

G26 or G38

Looking for 2 of the G26 or G38 for project
Forum: Marketplace
05-03-2018, 05:46 PM
Replies: 7
Views: 568
Posted By dnimigon

Boxes

Boxes look water touched. Hows the inside. Any other pics you might have.
Forum: Marketplace
04-15-2018, 02:24 PM
Replies: 1
Views: 619
Posted By dnimigon

What is the wingspan on this guy. I live in...

What is the wingspan on this guy. I live in Alberta just west of Edmonton
Forum: Marketplace
04-02-2018, 04:41 PM
Replies: 0
Views: 368
Posted By dnimigon

G26 or G38 Aircraft engine. Pair of each

Looking for a pair of G26 or G38 engines for aircraft use.
Forum: Marketplace
04-01-2018, 08:58 AM
Replies: 9
Views: 607
Posted By dnimigon

Shipping

Can you tell me more on this engine. How old would it be and about how many hours on it. Will you ship to canada
Forum: Giant Scale Aircraft - General
03-13-2018, 06:34 PM
Replies: 116
Views: 43,934
Posted By dnimigon

Tried looking up Probuilder. All kinds of crap...

Tried looking up Probuilder. All kinds of crap comes up. Do you have a link for them.
Forum: Giant Scale Aircraft - General
03-02-2018, 04:30 PM
Replies: 116
Views: 43,934
Posted By dnimigon

I'm looking for the cowl also and windscreen. Are...

I'm looking for the cowl also and windscreen. Are they still being made. Even if I had the cowl it would be great. I could form my own but that takes a long time getting ti right.
Forum: Giant Scale Aircraft - General
02-19-2018, 07:26 PM
Replies: 5
Views: 777
Posted By dnimigon

Plan gluing

Been a builder for long time and have always had an issue with getting the plan cutout off the ply and balsa. I've usually used a contact type spray to glue the plan part (wing rib, etc) to ply or...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.