Search: Posts Made By: kommander
Showing results 1 to 25 of 66
Search took 0.54 seconds.
Forum: Control Lines
01-09-2016, 10:16 AM
Replies: 6
Views: 928
Posted By kommander

Can't that engine still be purchased from MECOA.

Can't that engine still be purchased from MECOA.
Forum: Q-500 Racing
10-30-2015, 05:32 PM
Replies: 4
Views: 1,214
Posted By kommander

I think he meant a whambop. Full size wing plan,...

I think he meant a whambop. Full size wing plan, a Bob Harris design!
Forum: Control Lines
09-05-2015, 04:55 PM
Replies: 3
Views: 798
Posted By kommander

K&B green head parts

Does anyone know if a back plate gasket and prop drive washer is available for a green head .35? Thanks Bruce
Forum: Q-500 Racing
11-13-2013, 08:05 AM
Replies: 9
Views: 1,360
Posted By kommander

I beg your pardon, the response to original post...

I beg your pardon, the response to original post is correct!
Forum: Q-500 Racing
11-12-2013, 09:37 PM
Replies: 9
Views: 1,360
Posted By kommander

The long stroke version cast case is the highest...

The long stroke version cast case is the highest performance Jett Q500 engine
Forum: Q-40 Racing
02-09-2013, 04:12 PM
Replies: 15
Views: 1,486
Posted By kommander

RE: finishing problems

Thanks for all the input, how about the de-greaser / wax remover. Any recommendations or should I not be using it?
Forum: Q-40 Racing
02-08-2013, 06:19 PM
Replies: 15
Views: 1,486
Posted By kommander

RE: finishing problems

PCL Poly prime
Forum: Q-40 Racing
02-08-2013, 05:22 PM
Replies: 15
Views: 1,486
Posted By kommander

finishing problems

I have gone to the local sign shop for some paint masks. He assures me that they are low tack and he's never had a problem. I am using single stage polyurethane for the base color and two stage for...
Forum: Q-40 Racing
01-12-2013, 08:31 AM
Replies: 14
Views: 1,555
Posted By kommander

RE: Futaba Setup

OK, I'm taking the regulator out of Joanne's airplane!!
Forum: Q-40 Racing
01-11-2013, 07:12 PM
Replies: 14
Views: 1,555
Posted By kommander

RE: Futaba Setup

I was in error, I'm using the orion pack too and the voltage is 6.9v after charge. Dare I take all my regulators out!
Forum: Q-40 Racing
01-10-2013, 08:00 PM
Replies: 14
Views: 1,555
Posted By kommander

RE: Futaba Setup

Since Futaba and JR don't recommend operating servos above 6.0 volts, and a life battery will charge up to 7.2 volts, isn't there a risk of premature sevo failure?
Forum: Q-500 Racing
10-18-2012, 08:14 AM
Replies: 18
Views: 1,982
Posted By kommander

RE: pics of mh27

Duane, If you want a resin that is clear and doesn't yellow you might want to try Aerospace Composite Products E-Z lam. It comes with two choices of hardener 1/2 hr. & 1 hr.
It's...
Forum: Q-500 Racing
10-16-2012, 01:53 PM
Replies: 18
Views: 1,982
Posted By kommander

RE: pics of mh27

Actually there was a race in Woodland in September & there will probably be one in Sept. 2013. Quickie has changed in the last year, it now requires a spec engine which is the Jett 40 or 426 engine. ...
10-02-2012, 08:02 AM
Replies: 40
Views: 3,732
Posted By kommander

RE: NMPRA Fall Gold Cup Race 2012 @ Old Julian Airport - Sept 29th & 30th

I was wondering if Bob Harris has plans available for his all wood quickie with bulit up wing. Thanks Bruce
Forum: Q-500 Racing
04-25-2012, 08:04 AM
Replies: 21
Views: 2,293
Posted By kommander

RE: TT 40Pro endplay?

I can't believe this post died with so much mis-information! The only one that is correct is dlyon.
Forum: Q-500 Racing
01-08-2012, 09:31 PM
Replies: 4
Views: 756
Posted By kommander

RE: Primer/Surfacer

I have used it and it worked well, I liked it because it is white. After several years rust developed in the can!! Now I use poly prime from PCL ( pacific coast lacquer ) it's the best I have found...
12-11-2011, 09:06 PM
Replies: 3
Views: 887
Posted By kommander

RE: Nelson 40 Help

If your crankshaft is 19mm in diameter I believe you assemble the balls directly on the crankshaft along with the outer race of the bearing. I think you need a 30X17X7mm bearing then pop out the...
Forum: Q-40 Racing
09-28-2011, 02:41 PM
Replies: 7
Views: 1,345
Posted By kommander

RE: Fred Burgdorf Tribute Race

D. E. Just wanted to thank you for the painting & finishing tips. This is my latest, it's a GR7 from Matt Russell. I've eliminated the cowl & canted the motor down, got rid of the gravel...
Forum: Q-40 Racing
09-28-2011, 02:34 PM
08-24-2011, 07:42 AM
Replies: 7
Views: 1,044
Posted By kommander

RE: reciver

Well, there's the definitive answer. Randy, check out the rebuilt quickie!!
Forum: Q-500 Racing
06-05-2011, 05:53 PM
Replies: 2
Views: 933
Posted By kommander

Quickie - Coffinator

This is a quickie Ben & I built for a friend. It was started over five years ago when the govenator was in office, thus the name..
Forum: Q-40 Racing
05-05-2011, 08:59 AM
Replies: 95
Views: 15,416
Posted By kommander

RE: MUBU II F5D Build

Hi Dave, very nice work!! Have a question about rubbing out paint. I have a quickie wing that I have to paint the bottom. I sanded it with 1500. then buffed it out with a foam pad in a drill press....
Forum: Q-500 Racing
04-01-2011, 09:28 AM
Replies: 4
Views: 1,181
Posted By kommander

RE: QJ-2 Jett engine ?

The QJ-2 is a Quickie Jett. It is the second generation of the cast case. Most people that run the Jett use the Merlin "red" plug. Not sure about Props.
Forum: Q-40 Racing
03-10-2011, 01:53 PM
Replies: 1
Views: 1,317
Posted By kommander

RE: What Q40 airplane is this???

Oddy, It's an H&M racing Loki from the early 90's.
Showing results 1 to 25 of 66
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service