Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Randy M.

Page 1 of 40 1 2 3 4

Search: Search took 0.87 seconds.

  1. Would you mind sharing control throws, cg, flap...

    Would you mind sharing control throws, cg, flap setting? I'm getting closer to maiden on mine. No bells and whistles on mine. Single k180. Should be under 38lbs.
    yours looked and sounded awesome. ...
  2. Replies
    332
    Views
    23,534

    I have a left

    I have a left
  3. Replies
    42
    Views
    1,538

    Ditto what Gary said

    Ditto what Gary said
  4. Replies
    42
    Views
    1,538

    I would do some calculations on the horizontal...

    I would do some calculations on the horizontal stab pivot position. It seems that most of the issues have been with full flying stabs. Pivot seems to be a little aft of where it should be. And make...
  5. Thread: Dx 18

    by Randy M.
    Replies
    6
    Views
    445

    Actually it comes with a 10 channel rx. Battery...

    Actually it comes with a 10 channel rx. Battery port is aux 5. For 18 you'll need the x plus module the plugs into the receiver. If you just need 12 channels you can use a 12 channel spektrum...
  6. Replies
    332
    Views
    23,534

    I wouldn't worry much about the reflex. Just be...

    I wouldn't worry much about the reflex. Just be prepared on take-off. Make sure to have plenty of trim available. Maybe put about a quarter inch in for test flight.
  7. Replies
    332
    Views
    23,534

    I would be interested in a kit if it doesn't...

    I would be interested in a kit if it doesn't break the bank
  8. Replies
    9
    Views
    634

    My friend makes a nice plug of aluminium with...

    My friend makes a nice plug of aluminium with knurled edges. About 1/2" diameter so my clumsy hands can grab it easily. Is a nice fit. Kiss is always best. Good advice above about fueling pressure...
  9. Replies
    9
    Views
    634

    Just a plug. Nothing fancy.

    Just a plug. Nothing fancy.
  10. I lost a 1/7 fej F18 on the maiden about 2 years...

    I lost a 1/7 fej F18 on the maiden about 2 years ago. Really bummed out for a few days. Certainly could not afford to replace it right away. Still building on the replacement. Hopefully will have...
  11. Replies
    7
    Views
    548

    Where is Eddie weeks when you need him?

    Where is Eddie weeks when you need him?
  12. Replies
    2
    Views
    193

    5 degrees total. You should be good to go.

    5 degrees total. You should be good to go.
  13. Replies
    21
    Views
    839

    Make sure it's the right expo also. Depending on...

    Make sure it's the right expo also. Depending on radio, futaba or jr, positive and negative are opposite. If that makes sense.
  14. Replies
    21
    Views
    839

    what about elevator setup? how much throw and...

    what about elevator setup? how much throw and expo?
  15. Replies
    21
    Views
    839

    I have the arf version. k100 engine. a lot of...

    I have the arf version. k100 engine. a lot of flap, no crow. cg at 7in. back. no elevator/ flap mix. lands nicely, rolls out about 30ft. less if i use the brakes. take it up high and cruise around...
  16. Replies
    15
    Views
    1,031

    2065507 these will go in my big F18. Using...

    2065507
    these will go in my big F18. Using 100oz dubro for the main tank and two 35oz for saddles. The clunks are drilled out and the brass the brass tube is soldered in place. barbs on all brass...
  17. Replies
    16
    Views
    543

    May do it at some point. We have access to pretty...

    May do it at some point. We have access to pretty good pavement. Have bigger fish to fry for now.
  18. Replies
    16
    Views
    543

    I have one as well. I also have a k100 without a...

    I have one as well. I also have a k100 without a home. I figured it was not a good fit but will look into it now. Could do away with flaps and ailerons to same a little weight. Mine had been flown...
  19. just a hand drill with impact setting

    just a hand drill with impact setting
  20. would be cool but is a small market. i would get...

    would be cool but is a small market. i would get one
  21. basimp offers good advice however, to do that...

    basimp offers good advice however, to do that you would have to remove the outer can. just another pia. the copressor wheel is a pretty tight fit and should not move while removing the nut. a couple...
  22. use a small impact gun. electric drill type. it's...

    use a small impact gun. electric drill type. it's not super tight, but it is left hand threads. getting the correct nut may be a challenge. amt netherlands should have it.
  23. Replies
    4
    Views
    220

    i may have one tommy. I'll check and text you...

    i may have one tommy. I'll check and text you later
  24. sequencing in the dx18 is awesome. a little...

    sequencing in the dx18 is awesome. a little programming and it's done. have to program both directions. works great with electric gear and servo operated doors. could use simple robart valves and a...
  25. Replies
    394
    Views
    17,356

    Zeeb, that's kind where we left it. My radio...

    Zeeb,
    that's kind where we left it. My radio has latest update. The other did not. Rx was same rx. I bought the plane with the rx in it the only thing different is my tx. I'm done for now. May...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 09:08 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.