Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: w8ye

Page 1 of 40 1 2 3 4

Search: Search took 1.61 seconds.

  1. Replies
    911
    Views
    68,297

    Sounds as though you included everything that was...

    Sounds as though you included everything that was on you mind?
  2. Replies
    911
    Views
    68,297

    I would be afraid to stand around some of you...

    I would be afraid to stand around some of you guys with your flimsy test stands. A 38cc four stroke has some strong impulses

    This one is bad enough. There's just not enough meat in a Work Mate...
  3. Replies
    911
    Views
    68,297

    You guys settle down and quit bickering or I'll...

    You guys settle down and quit bickering or I'll take out the posts pointing at others.
  4. You can just epoxy a wooden dowel in the old...

    You can just epoxy a wooden dowel in the old spark plug.
  5. Replies
    9
    Views
    303

    I was thinking it was the later part of the 80's...

    I was thinking it was the later part of the 80's when he first started.

    Some C&H conversions back then are hard to distinguish from Ralph Cunningham conversions.
  6. Thread: break in oil

    by w8ye
    Replies
    14
    Views
    367

    Use the same oil and ratio as you plan to use for...

    Use the same oil and ratio as you plan to use for the life of the engine.
  7. Replies
    3
    Views
    103

    Check for an air leak in the suction hose above...

    Check for an air leak in the suction hose above the fuel level and where it connects to the pump.

    If the hose and connections are OK then the shaft seal on your pump is gone.
  8. Replies
    9
    Views
    227

    I have a Medtronics Defibrillator and I run...

    I have a Medtronics Defibrillator and I run chainsaws and weed whackers. I keep them on my right side and run "R" plugs. It's been seven years. I don't look under car hoods with the engine running. I...
  9. The fuel regulator diaphragm that opens the...

    The fuel regulator diaphragm that opens the needle you mentioned, needs a vacuum in the venturi of the carburetor to open the needle. It is a demand regulator.

    You need to read the article about...
  10. Replies
    21
    Views
    432

    This is normal

    This is normal
  11. Replies
    44
    Views
    3,059

    The line routes the atmospheric side of the fuel...

    The line routes the atmospheric side of the fuel regulator to air inside the fuselage rather having air in the engine cowling blowing over the vent hole.
  12. Replies
    9
    Views
    386

    +1

    +1
  13. Replies
    26
    Views
    382

    I've been running one of these "C" cams for some...

    I've been running one of these "C" cams for some 10 years and the engine with the car cam doesn't run any different than the other three engines I have with regular cams.

    The total lift is the...
  14. Thread: Tillotson Carbs

    by w8ye
    Replies
    5
    Views
    124

    There are some Chinese carbs on import engines...

    There are some Chinese carbs on import engines that say Tillotson on them. But they are more of a Walbro copy. Tillotson's factory is in Ireland.

    At any rate, they are set just like Walbro carbs. ...
  15. Replies
    13
    Views
    332

    You may be putting too much emphasis on reading...

    You may be putting too much emphasis on reading the spark plug?

    OK, so you looked at it ! The correct spark plug was the correct color. Time to forget the spark plug. You are going to ruin the...
  16. Replies
    28
    Views
    722

    I have been very good at evaluating a engine IN...

    I have been very good at evaluating a engine IN FLIGHT and then turning the engine off on the ground and adjusting the needle valves.
  17. Replies
    6
    Views
    125

    I remember this being discussed a few times...

    I remember this being discussed a few times before. It is in the threads for the DLE30 & DLE 20 . . . . somewhere?
  18. Replies
    6
    Views
    125

    A "WJ-71" is used on a DLE 111. It has a 18.25mm...

    A "WJ-71" is used on a DLE 111. It has a 18.25mm venturi
  19. Replies
    28
    Views
    722

    A very good post!

    A very good post!
  20. Replies
    28
    Views
    722

    Shut the engine off!

    Shut the engine off!
  21. Replies
    13
    Views
    332

    You are not necessarily running lean. 225-250F is...

    You are not necessarily running lean. 225-250F is a good range while in flight.

    There is a big unknown here . . .

    It is more important - the temperature the engine is running in flight with...
  22. Replies
    13
    Views
    332

    That's as high as you want to get

    That's as high as you want to get
  23. That's a Dolmar 120S jug and the engine is...

    That's a Dolmar 120S jug and the engine is probably a 4.1?

    That engine in the picture has a 49mm bore with a 36mm stroke and the Sachs 4.2 had a 47mm bore and a 40mm stroke.

    I would rather...
  24. Thread: Evolution Oil

    by w8ye
    Replies
    18
    Views
    502

    Stay with 32:1 with the 20cc engines.

    Stay with 32:1 with the 20cc engines.
  25. https://www.youtube.com/watch?v=GBXFpxWg7vY ...

    https://www.youtube.com/watch?v=GBXFpxWg7vY

    How to set timing
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 03:49 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.