Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Mikeup

Page 1 of 18 1 2 3 4

Search: Search took 0.39 seconds.

  1. I don't know where some of this info comes but a...

    I don't know where some of this info comes but a lot is incorrect. Motor heat with finger is 5 seconds for one. Water cooling by having perpendicular works great. Amount of water need not be a stream...
  2. Replies
    13
    Views
    399

    He posted the same thing on rcgroups and offshore...

    He posted the same thing on rcgroups and offshore with pictures and all.
  3. Replies
    13
    Views
    399

    Link- RCGroups and look for said subject. You...

    Link- RCGroups and look for said subject. You don't have to join, just look. People gave honest answers in a decent manner and wasn't smart about answers.
  4. Replies
    13
    Views
    399

    Your answers were on the other forum by Husky.

    Your answers were on the other forum by Husky.
  5. Replies
    6
    Views
    184

    //////.

    //////.
  6. Thread: Sam's Flatty

    by Mikeup
    Replies
    30
    Views
    637

    That airboat handled perfect, tho is was windy....

    That airboat handled perfect, tho is was windy. My hat goes off to you!
  7. Replies
    3
    Views
    174

    Hi, guy! Haven't seen you name for awhile. Your...

    Hi, guy! Haven't seen you name for awhile. Your right ! I discharged with 3 auto bulbs and a low voltage beeper and got it down to 3.0. Next like google mentions , I started charging at 1.0 and got...
  8. Replies
    3
    Views
    174

    I googled and found the answer.

    I googled and found the answer.
  9. Replies
    3
    Views
    174

    lipo with 1 cell lower than the other 2S

    Lipo is a 3.0 Turnigy 30c. I read where you can discharge a lipo some and charge at a low charge to bring it back with balance working. 1 cell reads 4.22- other cell reads 3.98, thanks for reading...
  10. ....

    ....
  11. .......

    .......
  12. Thread: RX issues?

    by Mikeup
    Replies
    2
    Views
    124

    I'd spray a little Corrosion - X into rx and let...

    I'd spray a little Corrosion - X into rx and let set for 1 hour and then use a hair dryer and blow most of it out. Then lay rx on a paper towel in sunlight for few hours. When you remove the red wire...
  13. Replies
    4
    Views
    220

    Pull flex every day after running to clean and...

    Pull flex every day after running to clean and don't lube or insert flex till it is time to go boating. Reason; rust will occur if you insert and don't go boating for some time.
  14. Replies
    16
    Views
    391

    ,,,,,,,

    ,,,,,,,
  15. Replies
    16
    Views
    391

    .....,,,

    .....,,,
  16. Replies
    6
    Views
    216

    ......

    ......
  17. Replies
    6
    Views
    216

    .......

    .......
  18. Replies
    63
    Views
    7,294

    You're having to much FUN!

    You're having to much FUN!
  19. Replies
    12
    Views
    294

    My guess is the motor is amp hungary. Lower your...

    My guess is the motor is amp hungary. Lower your kv down to 880 on 6S.
  20. Replies
    158
    Views
    4,300

    Induced flat turns were slow speed and close...

    Induced flat turns were slow speed and close radius while bigger turns were no change at all from video. Correct!
  21. I don't own any video equipment and never given...

    I don't own any video equipment and never given it much thought.
  22. I just remembered, I have a Kershaw 650S brushed...

    I just remembered, I have a Kershaw 650S brushed motor which runs on 12v+ with a 1/8" motor stem. The specs say 14.8-16.8volts. Motor runs best on 12v+. Do you have any brushed equipment? I did put...
  23. The motor is a inrunner 36 4 3900 on 2S with a...

    The motor is a inrunner 36 4 3900 on 2S with a 535 Octura prop and speed will be in the high 30,s. They quit making them some time ago and had several of them and are in 22" boats.
  24. Still around. What happened to the other boats?...

    Still around. What happened to the other boats? You'll like the flood chamber! Your CG is 7.8" from transom. The m/mount depends if you use 2 lipos or just one lipo. 2 lipos, I would place m/mount at...
  25. Replies
    158
    Views
    4,300

    .......

    .......
Results 1 to 25 of 433
Page 1 of 18 1 2 3 4
All times are GMT -6. The time now is 05:08 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.