Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: trpastor

Page 1 of 33 1 2 3 4

Search: Search took 1.13 seconds.

  1. Replies
    2,427
    Views
    207,167

    RE: RCAero JC Engines & YDA Engines

    Let's not forget price point. The engines are close in power - that is pretty obvious. The JC is even lighter than the rear carb version of the DLE. The Side carb had issues (maybe, who knows). ...
  2. Replies
    2,427
    Views
    207,167

    RE: RCAero JC Engines & YDA Engines

    Most honest people who were reading that exchange could read the hearts of the posters. I have seen some pretty great intentions and customer service from Henry. And Bambi's mom always said, if you...
  3. Replies
    10
    Views
    3,585

    RE: Sbach 50cc Goldwing

    n.
  4. Replies
    44
    Views
    7,392

    RE: Redwing RC 30cc 3D planes

    just look at 3:05... the way it picks up out of knife edge and shoots in the air, I would say it's PLENTY for the plane. The JC is actually 2oz lighter than the new rear carb DLE. hope this helps
  5. Replies
    2,427
    Views
    207,167

    RE: RCAero JC Engines & YDA Engines

    Hey Bart -

    It is a new dry carb. I had the same problem the first time. You can try to prime it with some fuel straight to the carb as you suggested. That will help the suction. And then...
  6. Replies
    17
    Views
    1,871

    RE: SBach Video - Redwing RC fixed link!

    I lfd
  7. Replies
    2,427
    Views
    207,167

    RE: RCAero JC Engines & YDA Engines

    I like what I hear on it - what planes do some of you have these in?
  8. Replies
    2,427
    Views
    207,167

    RE: RCAero JC Engines & YDA Engines

    That's great news!
  9. Replies
    2,427
    Views
    207,167

    RE: RCAero JC Engines & YDA Engines

    nice reply!!!
  10. Replies
    3
    Views
    513

    Testing Servos - Will I Damage them??

    Hey Guys - I was going to do a little servo testing. I was going to set them up on a stand and see what kind of torque they have. So I was going to put on a 1" arm and put on 120oz (for a 120oz/in...
  11. Servo has no strength in ONE direction?!

    Hey guys - I have an old servo I was thinking of using, until I realized that if you pull on it one way you can easily pull it back to neutral. the other direction seems to be holding just fine. ...
  12. Properly Setting up a Pull Pull rudder?????

    I was wondering if anyone had an article on setting this up properly? I know some dual servo arms come with an offset, but I've never really understood the theory behind it. I'm sure it's fairly...
  13. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    Once question - the carb is turned so that the needles are tilted towards the prop... I don't think I can tune with it running ?
  14. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    Cool, thanks guys... I'll ready up. I'm ok at it but not great, so it looks like this will help out a lot
  15. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    Any tuning advice on this engine? It's going pretty wel, but it's hesitating if i let it idle and than punch it to mid throttle. I'm thinking low end too rich but is there a good article on tuing...
  16. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    Hey guys... recommendations on best prop for 3d with this engine? On a 10.5lb 73" plane?
    18*6 or 19?
  17. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    I should have mentioned that. I am using a drill press

    thank you for your help!
  18. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    Hey Guys

    Is there any problem with using my pressure plate as a guide to drill the holes in my prop? I was going to get a (10mm?) bolt and nut and sandwich the plate between the prop and the...
  19. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    that's IF you don't cut out the mountbox to let the carb sit inside the mountbox, correct? You can drop it back to where the original version was if you cut it open?
  20. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    cool, thanks for the advice. I'll get it going and let you all know what I find with mine
    thanks
  21. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    I have one I'm looking to get started today or tomorrow. Can anyone give me any last minute tips on how to start and break in this new engine?

    I can appreciate your stance that people are...
  22. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    Another question - is the rear carb taking care of the issues that had been seen with this engine? I haven't followed this thread, but it sounds like some had done this mod on their own?

    So,...
  23. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    If the hub is going to be 30mm past the old version, that's going to create some problems for some of these planes that have been designed around the original version - isn't it?
  24. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    What is the overall length now? (from stand offs to prop hub)?
  25. Thread: DLE30!

    by trpastor
    Replies
    5,231
    Views
    580,169

    RE: NEW DLE30!

    Ok guys - I'm getting ready to start install the DLE 30 I have. Couple questions

    The throttle arm is set up sideways. Can this be turned so it runs paralell to shaft, so it's easier for a...
Results 1 to 25 of 823
Page 1 of 33 1 2 3 4
All times are GMT -6. The time now is 11:39 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.