Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: subbass

Page 1 of 3 1 2 3

Search: Search took 1.03 seconds; generated 56 minute(s) ago.

  1. Replies
    10
    Views
    3,685

    I lost my manual for my eagle 50 can I get...

    I lost my manual for my eagle 50 can I get another one?
  2. Replies
    40
    Views
    2,185

    RE: Trouble starting new Turnigy Thunderbolt

    25 to 1?Sounds like to much oil to me and is fouling your plug.Manual my be wrong?I would try 40 to 1 and a new plug.
  3. Does anybody make 1/10 buggy paddle tires anymore?

    Can't seem to find any 1/10 2.2 buggy paddle tires,Anybody make these anymore.
  4. Replies
    31
    Views
    1,817

    RE: Savage half tank EXTREME lean problem.

    Have you tried a new tank?Does the engine lean out when the fuel level reaches the tank halfs it may have a tiny leak there.
  5. Replies
    17
    Views
    835

    RE: No more novak

    Thank you somebody is paying attention,I am just stating the fact that novak sent me two bad motors at once.These guy's talk like there sponsored by novak or something.
  6. Replies
    17
    Views
    835

    RE: No more novak

    I find it funny that you think I expect perfection from novak,But there are better systems I will be using later thats why I am not sending the stuff back.I will probably sell the bad motors,The only...
  7. Replies
    17
    Views
    835

    No more novak

    I purchased two motors from the novak store recently,A rebuilt novak 13.5 ss that failed only after 10 minutes of operation.The motor was not overgeared and running cool.The other motor is a new...
  8. Replies
    10
    Views
    834

    RE: CEN 7.7gst break in

    As long as you have smoke coming out of the engine at all RPMs you will be ok,If the glow plug is gray in color that is good but not if the coil is distorted.If you ran the engine a little lean it...
  9. RE: Stumped: Engine acts erratic on LSN richening

    Good job enjoy.
  10. Replies
    24
    Views
    1,237

    RE: Shock options for 1/8 buggies

    I have a savage x that uses only 3mm shockshafts and I only use four shocks instead of eight and I have not bent or broken one yet.Don't get me wrong I beat on my sav but not to the point of...
  11. Replies
    24
    Views
    1,237

    RE: Shock options for 1/8 buggies

    Your friend bends shockshafts left and right?Sounds like improper use to me,Why don't I have that problem?Everybody is quick to blame the car and not themeselves.
  12. Replies
    9
    Views
    776

    RE: bench break in Q's

    I agree with 378 it is best to breakin in the car,Just be patient.
  13. Replies
    3
    Views
    418

    RE: Hyper 7 compatible shock options

    Unless your racing just stick to the OEM stuff,I have a hyper7 and the stock shocks are good for just bashing around.You can get better shocks but ther a lot more costly.
  14. Replies
    24
    Views
    1,237

    RE: Shock options for 1/8 buggies

    Why don't you just get the OEM parts from kyosho?
  15. Replies
    10
    Views
    834

    RE: CEN 7.7gst break in

    Remember breakin should be done close to normal operating temps(180F min)But at lower RPMs.It is not good to run it cold(under 180F).
  16. Replies
    10
    Views
    553

    RE: High erratic idle after changing fuel??

    Never use fuel color dye in it,If you ask me I consider color dye a contaminant and does lower engine performance.I notice some fuels have more dye in them than others,Still the best fuels are the...
  17. Thread: tamiya cc01

    by subbass
    Replies
    36
    Views
    3,433

    RE: tamiya cc01

    This is ok if you plan to putt around with it somtimes,But if you want something that you can use everyday and is more durable,Can take more power I would go with a traditional 4wd set up like the...
  18. Replies
    10
    Views
    834

    RE: CEN 7.7gst break in

    To check the engine for air leaks start the the engine and plug the carb with your finger(stay clear of moving parts)the engine should stop instantly.If not there is a airleak check area were the...
  19. RE: Stumped: Engine acts erratic on LSN richening

    How hot is it getting?Breakin should be done close to normal operating temps(180F minimum) .The only way to make sure fuel lines are good is to replace them with new line.The tank should be submerged...
  20. Replies
    40
    Views
    1,910

    RE: Crank Bearings

    I alway's used marvel mystery oil for after run oil,I never use wd-40.
  21. Replies
    40
    Views
    1,910

    RE: Crank Bearings

    After running the engine alway's disconnect the fuel line and run the engine until it stops firing(you may have to start it a few times until it is completely clear of fuel) and then use after run...
  22. Replies
    19
    Views
    3,257

    RE: Epoxy will not cure.

    Thanks for the info guys.
  23. Replies
    19
    Views
    3,257

    Epoxy will not cure.

    I have some epoxy that has not cured in 4 days now(still like taffy),I have used epoxy for many years with no problems.
    It may be old its 30min epoxy,Is there any way to fully cure this epoxy.[:@]
  24. Replies
    2
    Views
    474

    RE: Does norvel still make engines.

    Thanks for the info,I have a 061 ame with about quart fuel ran through it.Still in great shape,Too bad they went out of business,
    they were good engines.
  25. Replies
    2
    Views
    474

    Does norvel still make engines.

    Does anybody know were to get engines or parts from norvel,Are they still making them?Any info will help.;)
Results 1 to 25 of 63
Page 1 of 3 1 2 3
All times are GMT -6. The time now is 12:04 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.