Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: KC36330

Page 1 of 40 1 2 3 4

Search: Search took 1.08 seconds.

  1. Replies
    12
    Views
    882

    RE: Surging on Acceleration (again)

    No, it only resets the PID loops. Atmospheric conditions (determined with algorithms during previous runs) are stored and used by the ECU, sometimes when the turbine has sat unused this algorithm can...
  2. Replies
    12
    Views
    882

    RE: Surging on Acceleration (again)

    Hold Manual on the GSU and slowly advance thrust while continuing to hold it down and continue holding about 30 seconds. It will reset the PID loops and should clear up the issue.
  3. Replies
    21
    Views
    1,610

    RE: Can't learn Rc

    Binding at 150% and doing the Learn RC at 75% gives higher resolution then the 100/50.
  4. Replies
    20
    Views
    2,148

    RE: Tamjets Servo Mounts

    that's been my experience with them as well, i use CA in the center to hold them down while the epoxy/hysol around the outer edges dries. can't even rip them off to reuse them later without...
  5. Replies
    21
    Views
    1,610

    RE: Can't learn Rc

    See if you can do the Learn RC with the button on the IO board.
  6. Replies
    21
    Views
    1,610

    RE: Can't learn Rc

    Does the value on the GSU change if you move the throttle stick?
  7. Thread: Powerfail

    by KC36330
    Replies
    5
    Views
    522

    RE: Powerfail

    power fail is loss of power from the receiver.
  8. Replies
    21
    Views
    1,610

    RE: Can't learn Rc

    yes it is, you bind for failsafe with 150%, reduce to 75% and learn RC works perfect.
  9. RE: C-ARF Flash Build Thread for All Flash's being built this winter

    looks good!!
  10. RE: C-ARF Flash Build Thread for All Flash's being built this winter

    the pic's were of Douggy's old classic flash and my classic flash, they are just Velcro'd in, it works great. the wing holds them in place in flight and the Velcro when the wing is off.
  11. Replies
    71
    Views
    4,019

    RE: Info from Data Terminal after a shutdown

    the FADEC monitors your requested RPM and it does it's part to get the turbine to match that, the acceleration/deceleration parameters determine how quickly it's allowed to do that, the rapid back...
  12. Replies
    71
    Views
    4,019

    RE: Info from Data Terminal after a shutdown

    the video shows no fault of the turbine, it runs fine up till you start jamming the throttle stick up and down to induce a fault (the pump can't possibly keep up with your up/down/up/down demands),...
  13. Replies
    71
    Views
    4,019

    RE: Info from Data Terminal after a shutdown

    that's a turbine engine, not a harley at a red light, you don't rev the engine up and down like that, that video was useless IMO.
  14. Replies
    71
    Views
    4,019

    RE: Info from Data Terminal after a shutdown

    while it does sound like a pump it could also be a solenoid closing at high flow if plumbed in backward or anything between the pump and turbine, try disconnecting the tube from the turbine and test...
  15. Replies
    2
    Views
    295

    RE: Running P-70 without TX/RX

    plug the throttle channel into the airspeed port on the ECU, when you plug the battery in, the ECU will power on, you can then use the GSU to fully control the turbine, it's all covered in the...
  16. Replies
    53
    Views
    4,123

    RE: President Proposes RC Airplane User Fee

    CoolPower fuel is as "going green" as I'm going!!
  17. Replies
    53
    Views
    4,123

    RE: President Proposes RC Airplane User Fee

    he's an idiot, nothing joking about it.
  18. Replies
    53
    Views
    4,123

    RE: President Proposes RC Airplane User Fee

    http://www.aero-news.net/ANNTicker.cfm?do=main.textpost&id=cd0ef175-2392-4166-ba09-bc0124a1e717
  19. Replies
    53
    Views
    4,123

    President Proposes RC Airplane User Fee

    I'm sure some of you have heard this mornings news about that idiot wanting us to pay 10 bucks per flight for airspace user fee..........seams it's the 'Top 1% wage earners flying these expensive...
  20. Replies
    1
    Views
    370

    RE: Powerup ECU at PC

    plug the throttle or aux into the airspeed port then plug the ECU battery in.
  21. Replies
    13
    Views
    559

    RE: P60 not running at max RPM

    for a P60 it should run about 1.7v depending on fuel system.


    try taking it to full power and let it stabilize, then press and hold manual key and hold for about 30 seconds and see if the...
  22. Replies
    13
    Views
    559

    RE: P60 not running at max RPM

    What is max RPM set at?
  23. Replies
    13
    Views
    559

    RE: P60 not running at max RPM

    While at idle, hold the manual key. SLOWLY accelerate the turbine to full (take at least 10 seconds to make the transition)

    Leave the turbine running at full power for about 20-30 seconds....
  24. Replies
    7
    Views
    868

    RE: Flybarless for a newbie

    you can't beat the Compass/TracX head for the Raptor
  25. RE: Flush out vibration with flybarless beastx heli

    do a blades off run and keep an eye/ear tuned on it for vibes or swash movement.
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 12:09 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.