Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: mysteryrc

Page 1 of 3 1 2 3

Search: Search took 0.43 seconds.

  1. Replies
    45
    Views
    1,643

    1 gallon Coleman fuel + 8oz quicksilver

    1 gallon Coleman fuel + 8oz quicksilver
  2. Have you tried it with the glow plug loose....

    Have you tried it with the glow plug loose. Traxxas fuel may not be the best, but should at least pop. Just noticed you are spinning it right. Most marine engines spin left looking from prop. Not...
  3. 21249262124927 Here is a better pic of the step....

    21249262124927
    Here is a better pic of the step. Also a pic of the bottom of the hull. All the reinforcing of the bottom of hull was done from the inside of the hull.
  4. 2124917212491821249192124920 Here are some more...

    2124917212491821249192124920
    Here are some more progress pics. Glassed a small block for an aluminum tank mount to be screwed down. It needs a velcro strap to hold the tank down though. I started...
  5. Replies
    11
    Views
    819

    What fuel/oil ratio are you using? What are your...

    What fuel/oil ratio are you using? What are your needle settings?
  6. Replies
    11
    Views
    819

    Also the dark blue lines, smaller ID than light...

    Also the dark blue lines, smaller ID than light blue? Check to make sure plenty of water is peeing when you make your passes. I run mine with cowl off. I had the same problem with my cowl on. I also...
  7. Replies
    11
    Views
    819

    I see a water line on your pipe may be hooked up...

    I see a water line on your pipe may be hooked up wrong. Water lines go in low, out on high. Someone may correct me if I'm wrong. Also the o ring on pipe stop holding pipe on. Mine has an aluminum...
  8. Replies
    11
    Views
    819

    Gizmomotors.com has everything you need.

    Gizmomotors.com has everything you need.
  9. Replies
    3
    Views
    413

    That is a car esc. If it gets wet it might go "up...

    That is a car esc. If it gets wet it might go "up in smoke"
  10. Replies
    2,876
    Views
    253,775

    what they said.:cool:

    what they said.:cool:
  11. I have seemed to find a thread on rc groups about...

    I have seemed to find a thread on rc groups about the pressure line problem I am having. It seems it will run without the line. If all else I will tap the muffler for pressure fitting.
  12. Replies
    8
    Views
    625

    I had the viper many years ago. ESC went up in...

    I had the viper many years ago. ESC went up in flames. Only thing I have left is the stock Lemans 540. Lol.
  13. Fuel tank setup?

    So I have started looking for a way to mount my fuel tank. I am going with a 16 oz. tank. It has a fuel inlet, and pressurized line for muffler. I am not sure if I need to add a pressure fitting to...
  14. I still need to mount fuel tank and radio box,...

    I still need to mount fuel tank and radio box, servos, etc. Also need to buy a 3/16" flexshaft with welded stub. The flexshaft I have is for use with brass ferrule. Any good links for one stop...
  15. Got the engine mounted finished. Some hardware...

    Got the engine mounted finished. Some hardware installed. I have been looking at rudders online. Thinking about a 130mm rudder w/ 75mm-80mm standoff. Here are some more pics. Trim tabs and turn fins...
  16. Replies
    1
    Views
    264

    Need pictures. I'm sure someone will be able to...

    Need pictures. I'm sure someone will be able to identify.
  17. Here is the converted K&B. Simple swap from air...

    Here is the converted K&B. Simple swap from air cooled head to water cooled head. Not super satisfied with the heliball muffler, but I don't want to spend any money on upgrades to the K&B. New motor...
  18. Here are some more pics of the hull. I will post...

    Here are some more pics of the hull. I will post more pics as I progress. I still need to install hardware, stuffing tube etc. I have had the K&B .40 mounted on aluminum angle mounts, with rubber...
  19. New Project... ( Fiberglassing Freedom Rz )

    Just doing this one for fun. Not sure how it will work out for me. Converting my ABC Hobbies Freedom Rz from outboard to inboard. I have gutted the boat and have started the glasswork. I have to...
  20. Replies
    3
    Views
    249

    Gizmo motors has what your looking for.

    Gizmo motors has what your looking for.
  21. Replies
    3
    Views
    249

    Fuji engine?I think you should get a 7/8 no leak...

    Fuji engine?I think you should get a 7/8 no leak flange and new 7/8 header with 7/8 pipe. The bolt pattern for the fuji and zenoah are the same. Then if you decide to upgrade to a zenoah you already...
  22. Having some trouble achieving full pitch due...

    Having some trouble achieving full pitch due flybar paddles. I need to shim up another 1/2" to get the flybar above fuselage to prevent contact. This will put my boomtube into the top of the tail...
  23. Parts fabricated. Still working out some of the...

    Parts fabricated. Still working out some of the bugs. Kill one bug, out comes another. May have some questions later for some of the experts here. I am trying to keep this a clean build, and do the...
  24. Replies
    36
    Views
    1,747

    Jag engines, or wackerengines.com

    Jag engines, or wackerengines.com
  25. Thread: VXL-3 esc?

    by mysteryrc
    Replies
    1
    Views
    137

    Well, I decided to solder it up. Now the...

    Well, I decided to solder it up. Now the bullet/bananna connectors are in good. I figured I was going to have the same issue, just by looking at the esc when I pulled it off to solder up. Looking at...
Results 1 to 25 of 58
Page 1 of 3 1 2 3
RCU Reviews
All times are GMT -6. The time now is 07:30 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.