Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: PHall

Page 1 of 3 1 2 3

Search: Search took 1.13 seconds.

  1. Replies
    45
    Views
    1,791

    I added it to my cart and standard shipping is...

    I added it to my cart and standard shipping is free. Two day shipping is $77. I think you chose 2 day shipping.
    2013502
  2. I purchased a plane and the canopy was slightly...

    I purchased a plane and the canopy was slightly damaged. In short, the response was very fast and professional. I am very pleased with my purchase.

    I would not hesitate to purchase another.
  3. Replies
    3,531
    Views
    391,733

    I have one gear that is "compressed" and one that...

    I have one gear that is "compressed" and one that isn't. By manually working the gear you can tell that one spring is easier to extend than the other. I'm going to get a new set of srings from...
  4. Replies
    3,531
    Views
    391,733

    I thought I would post a few pics of how I laid...

    I thought I would post a few pics of how I laid out my "radio" compartment. The first level is servos and air. The second level is fuel and switches. Four screws and the second level is removed for...
  5. Replies
    15
    Views
    506

    http://www.troybuiltmodels.com/items/QRI.html

    http://www.troybuiltmodels.com/items/QRI.html
  6. Thanks Jim! And I 100% agree. But.........we...

    Thanks Jim! And I 100% agree.

    But.........we assume that both saddle tanks will empty at the same time. If the first saddle tank empties before the second, then the remaining fuel in the second...
  7. So somebody explain to me why in the first...

    So somebody explain to me why in the first diagram the UAT will suck air and in the following diagrams the center tank will not suck air. No matter what you call the tanks, a tank is a tank and air...
  8. I would cut the cowl back on to match on both...

    I would cut the cowl back on to match on both sides. They say that the exist should be 3X the inlet. Have you flown without the cowl? Did it over heat?

    I helped with a project once that involved...
  9. +1

    +1
  10. The first thing would be to richen the mixture....

    The first thing would be to richen the mixture. It is alao the easiest. A bigger prop requires more horsepower and horsepower requires fuel. Simple. I would always run an engine as rich as possible...
  11. Replies
    190
    Views
    11,246

    http://upload.wikimedia.org/wikipedia/commons/thum...

    http://upload.wikimedia.org/wikipedia/commons/thumb/4/43/Location_North_America.svg/550px-Location_North_America.svg.png
  12. Replies
    190
    Views
    11,246

    & Greenland

    & Greenland
  13. Replies
    80
    Views
    2,976

    And also where the torque is measured in the...

    And also where the torque is measured in the stroke of the servo. You should look at the torque curves. Digital is exactly that. On or off. Analog varies its torque through its range. Digital is all...
  14. Replies
    1,604
    Views
    183,771

    RE: What Aircraft are you installing your DLE20

    I have never weighed it. I can tell you that a DLE 30 was waaaaay too much power and it flew heavy. I had to put the three li-ions behind the wing to balance it with the DLE 30. With the DLE 20 I...
  15. Replies
    1,604
    Views
    183,771

    RE: What Aircraft are you installing your DLE20

    70" Extreme Flight Extra 300 EXP. 18X6 Zoar. 18X6 Vess. Lots of power!
  16. Replies
    37
    Views
    1,332

    RE: Inverted OS .46 Floods

    When the engine is running the tank is pressurized. Therefore more fuel is provided than what gravity can provide. So tank location is not the problem. The excess fuel that builds in the bottom of...
  17. Replies
    35
    Views
    2,917

    RE: New plane doesn't fit in bed of truck

    You could probably just use this for the plane and many other things.
  18. Thread: tape residue

    by PHall
    Replies
    24
    Views
    985

    RE: tape residue

    Goo Gone
  19. RE: Yep another quetion thats been asked a thousand times

    I have used Honda HP for years at 40:1. Never any problems. But I did notice some carbon. I saw an engine that had been running Klotz techniplate and it was like new inside. Have not tried it yet.
  20. Poll: RE: Best Compound/Product for Exhaust Bolt Threads?

    +1
  21. Replies
    42
    Views
    3,025

    RE: LIFE battery charging in the plane question

    Long story made short....you get more usuable energy from a Life.
  22. Replies
    20
    Views
    1,351

    RE: LiPo battery low voltage

    I had a dead lipo. Decided to try charging as a nicad for a few minutes. I have heard of this being done before. I know it has worked before.

    I also know that my pack got hot within seconds. I...
  23. Replies
    30
    Views
    3,215

    RE: Need Modellbau V3 Tornado Input

    So I called Todd at Dreamworks. Very nice of him to take time out to look at RCU and very nice to offer the correct tiller. You don't get this service very often.
  24. Replies
    30
    Views
    3,215

    RE: Need Modellbau V3 Tornado Input

    Thanks for pics. What wheel wells did you use? And how about some bottom pics of the gear.
  25. Replies
    30
    Views
    3,215

    RE: Need Modellbau V3 Tornado Input

    I installed Robarts on everything.
Results 1 to 25 of 73
Page 1 of 3 1 2 3
All times are GMT -6. The time now is 06:57 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.