Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: sdnitro

Page 1 of 2 1 2

Search: Search took 0.22 seconds.

  1. Replies
    2
    Views
    285

    RE: earthquake clutch

    Ok thanks that one sure had me stumped
  2. Replies
    2
    Views
    285

    earthquake clutch

    I am installing a new clutch bell and clutch shoesin my earthquake and am not sure how the clutch shoesgoes back together. There is a spring included and in not sure how it hooks to hold the clutch...
  3. Thread: clutch bell

    by sdnitro
    Replies
    1
    Views
    236

    clutch bell

    Just wondering if it is difficult to change the clutch bell on my earthquake? Is there anything to worry about or is it easy to do.



    Thanks
  4. Replies
    7
    Views
    763

    RE: Earthquake 3.5 running trouble.help

    Try a new glow plug cheap and easy to do
  5. Replies
    3
    Views
    447

    RE: cold weather nitro

    Thats a good idea i'll try it.  I also like the snow shield, I have ran mine without and packed it so full of snow that the throttle would not work

    anymore.  Sounds like spring is finally on its...
  6. Replies
    3
    Views
    447

    RE: cold weather nitro

    ?
  7. Replies
    3
    Views
    447

    cold weather nitro

    I am trying to run my earthquake 3.5 outside in cold temps (20F). I start the engine inside and let it warm up a bit then take it outside. I have a sock around the heatsink to keep it warm but I will...
  8. Replies
    3
    Views
    365

    fuel priming

    I have an earthquake 3.5 and i was wondering if there was a primer for priming the engine for start up. I blow through the exhaust tube, which works fine, but a primer would work better i think.
  9. Replies
    7
    Views
    634

    RE: earthquake 3.5 steering

    The earthquake has such large tires everytime you hit something you have a pretty good chance of breaking parts.  Does anyone have any good

    ideas how to build a larger front bumper to protect the...
  10. Replies
    1
    Views
    233

    Glow Plug Ignitor

    Is there a better glow plug ignitor out there,I currently am running a redcat ignitor which doesn't always make a good connection. I test it with an old glowplug and usually you have to tip the...
  11. Thread: trans oil

    by sdnitro
    Replies
    2
    Views
    260

    RE: trans oil

    Thanks i'll keep running her dry than</p>
  12. Thread: trans oil

    by sdnitro
    Replies
    2
    Views
    260

    trans oil

    My earthquake has a two speed trans and i was wondering if i should add some oil or do these usually run dry withoul oil?


    Thanks
  13. RE: Diffs. to oil or not to oil that is the question

    Are the diff cases that tight to hold oil.&#160;&#160;I personally thing a heavy grease like automotive wheel brg grease would work well and stay in place.&#160; I

    can't make my earthquake diffs last so im...
  14. Replies
    10
    Views
    854

    RE: Earthquake 3.0 front Differential failed

    I have replaced both&#160;the diffs in my earthquake 3.5 several times and cannot make them last.&#160; The rear diff just went out driving on sand and

    less than a tank run time, and I installed the...
  15. RE: HSN fuel line banjo fitting air leak Earthquake 3.0

    I would suspect your fuel line has a pinhole in it.&#160; Chances are it is the line from the tank to the carb that is falty.&#160; The line from the exhaust to the

    tank would not let bubbles into the fuel...
  16. RE: HSN fuel line banjo fitting air leak Earthquake 3.0

    my earthquake 3.5 was also loose but i was not having an issue either, i did tighten it up because it should not be loose.&#160; If the fitting was left

    loose it would probably leak fuel only out at...
  17. Thread: I hate UPS

    by sdnitro
    Replies
    7
    Views
    852

    RE: I hate UPS

    A little super glue or epoxy would fix that right up.&#160; I believe you can contact ups and complain but it would probably be&#160;a pile of paperwork and a long waiting process.&#160;&#160;I would contact the seller...
  18. Replies
    2
    Views
    449

    RE: Throttle picture

    Thanks for the pic.&#160; That is what I thought I have no idea where this extra spring came from but it does not belong on my earthquake.. Thanks again
  19. Replies
    2
    Views
    449

    Throttle picture

    I have an extra spring left over and I believe it is part of the throttle and brake linkage. If anyone has a pic of their earthquakes throttle linkage i can figure out where this spring came from
  20. Replies
    9
    Views
    1,279

    RE: wont accelerate/shockwave clutch ?

    check your diffs mine don't last long in my earthquake.&#160; I have replaced the spur gear both diffs and the 2 speed gear box.
  21. RE: Making an 8E rear wheel drive instead of all wheel

    I just figured when you are using two difs the power is divided in&#160; half between two diffs.&#160; When you eliminate one diff all the power will be

    transfered to one diff instead of two.&#160; I agree with...
  22. RE: Making an 8E rear wheel drive instead of all wheel

    you could try removing the front drive shaft but your rear diff will be recieving twice the power that it is used to and will not last long, but the fun factor is hard to beat
  23. Replies
    1
    Views
    424

    spur gear trouble

    I bought a steel spurgear and was wondering if anyone has tried removing the friction material and using loc-tite instead. My problem is that my friction material is trashed and I don't want to wait...
  24. Replies
    4
    Views
    606

    RE: Earthquake 3.5 pullstart stuck ???

    try loosening the pullstart from the engine and see what happens before you pull the pull start and check the spring
  25. earthquake used to run but now it won't start

    I have almost run a whole gallon of nitro fuel through my earthquake 3.5 and now I can't get it started. It will fire a few times but wont take off and run. I have wrecked my pull start spring and...
Results 1 to 25 of 42
Page 1 of 2 1 2
All times are GMT -6. The time now is 04:40 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.