Search: Posts Made By: joeflyer
Showing results 1 to 25 of 500
Search took 1.03 seconds.
Forum: Marketplace
07-19-2019, 10:45 AM
Replies: 2
Views: 240
Posted By joeflyer

Who manufactures this ARF?

Who manufactures this ARF?
Forum: RC Jets
07-15-2019, 02:56 PM
Replies: 1,906
Views: 306,076
Posted By joeflyer

My wing incidence is not fine. Wing LE is about...

My wing incidence is not fine. Wing LE is about 1/2 inch lower than the TE. That's why I'm concerned.
Forum: RC Jets
07-15-2019, 10:54 AM
Replies: 1,906
Views: 306,076
Posted By joeflyer

My L-39 is all together now. It sits with a...

My L-39 is all together now. It sits with a definite nose down attitude and I'm wondering how this will affect take offs. From pictures I've seen most seem to sit slightly nose down. Other models...
Forum: RC Jets
07-12-2019, 02:35 PM
Replies: 1,239
Views: 112,076
Posted By joeflyer

In my opinion a 100 would be the minimum for this...

In my opinion a 100 would be the minimum for this plane. The right engine is a 120. It should come out about 24# dry and about 30# TO weight. So you be the judge.
It also depends on whether...
Forum: RC Jets
07-05-2019, 05:10 PM
Replies: 10
Views: 470
Posted By joeflyer

I've used just the bottom half bypass on a couple...

I've used just the bottom half bypass on a couple of my jets. Since I was concerned about radiant heat from the tailcone after shutdown, I added aluminum tape to the rear several inches and that's...
Forum: RC Jets
06-27-2019, 04:07 AM
Replies: 9
Views: 984
Posted By joeflyer

Glad to hear that. I'm a few weeks away from...

Glad to hear that. I'm a few weeks away from maidening mine.
Forum: RC Jets
06-26-2019, 11:22 AM
Replies: 9
Views: 984
Posted By joeflyer

Thank you.

Thank you.
Forum: RC Jets
06-25-2019, 04:54 PM
Replies: 8
Views: 472
Posted By joeflyer

Please post the ebay link for the LED. ...

Please post the ebay link for the LED.

Thanks
Forum: RC Jets
06-22-2019, 04:30 PM
Replies: 9
Views: 984
Posted By joeflyer

1 inch seems more reasonable. I'll probably set...

1 inch seems more reasonable. I'll probably set my triple rates to 3/4, 1, and 1.25" for my maiden.

Any word on elevator/flap compensation?
Forum: RC Jets
06-20-2019, 03:38 PM
Replies: 9
Views: 984
Posted By joeflyer

Thanks, I'd appreciate that. Nice car too! ...

Thanks, I'd appreciate that.

Nice car too!

Joe
Forum: RC Jets
06-19-2019, 04:56 PM
Replies: 9
Views: 984
Posted By joeflyer

L-39 bvm pnp

Can someone confirm the recommended elevator throws and flap compensation for the BVM or Jet Legend L-39?

BVM PNP instructions say +1.5" and -1.25" for the elevator. That seems excessive. An old...
06-16-2019, 09:24 AM
Replies: 19
Views: 813
Posted By joeflyer

I had similar issues with my Falcon. The problem...

I had similar issues with my Falcon. The problem is due to the original restrictor being too small. For a while Jet Central was sending out a larger restrictor to customers who complained. I tried...
Forum: RC Jets
06-15-2019, 06:07 PM
Replies: 1,906
Views: 306,076
Posted By joeflyer

My L-39 finally arrived and I'm in the process of...

My L-39 finally arrived and I'm in the process of putting it together. Can someone confirm the recommended elevator throws and flap compensation?

BVM PNP instructions say +1.5" and -1.25" for...
Forum: RC Jets
06-12-2019, 01:21 PM
Replies: 4,997
Views: 965,821
Posted By joeflyer

Land slower.

Land slower.
Forum: RC Jets
05-23-2019, 01:39 PM
Replies: 1,906
Views: 306,076
Posted By joeflyer

All I need is lenses that will fit the tank tips....

All I need is lenses that will fit the tank tips. I'm sure Jet Legends or BVM would want to sell me a complete lighting kit (if they offer one). That's not what I want. I'm doing my own lighting...
Forum: RC Jets
05-21-2019, 04:45 AM
Replies: 1,906
Views: 306,076
Posted By joeflyer

Finally my L-39 is going to be shipped this week....

Finally my L-39 is going to be shipped this week. I'd like to add landing lights to the tip tanks. Does anyone have a source for tip tank clear lenses?
Forum: RC Jets
05-20-2019, 03:06 PM
Replies: 80
Views: 9,681
Posted By joeflyer

That doesn't answer the question.

That doesn't answer the question.
Forum: RC Jets
05-20-2019, 11:58 AM
Replies: 1,239
Views: 112,076
Posted By joeflyer

You'll have to sand and fit each block carefully...

You'll have to sand and fit each block carefully so that it just fits in the space available. You don't want to distort the upper wing skin.
Forum: RC Jets
05-20-2019, 11:36 AM
Replies: 80
Views: 9,681
Posted By joeflyer

Just wondering why this is being marketed as a...

Just wondering why this is being marketed as a Xicoy Turbine rather than a Jets Munt?
Forum: RC Jets
05-20-2019, 10:44 AM
Replies: 1,239
Views: 112,076
Posted By joeflyer

There are several ways you could do it. I made...

There are several ways you could do it. I made plywood blocks that tie the upper and lower wing skins together. Servos are mounted to the aluminum mounts then screwed into the plywood. I used flat...
Forum: RC Jets
05-17-2019, 06:55 AM
Replies: 1,239
Views: 112,076
Posted By joeflyer

I have a bit more downthrust than your latest...

I have a bit more downthrust than your latest picture. As long as it is directed away from the stab you should be OK. I haven't had any blistering problem. However, I did add some Flightmetal to...
Forum: RC Jets
05-16-2019, 04:30 AM
Replies: 1,239
Views: 112,076
Posted By joeflyer

Jeff, As discussed previously the cones...

Jeff,

As discussed previously the cones need to be cut down to fit. My rear former is recessed about 1/2 inch. I would not recommend trying to move the former. Shorten the wide end of the...
Forum: RC Jets
05-04-2019, 12:55 PM
Replies: 41
Views: 1,767
Posted By joeflyer

That's just a temporary fix. You haven't killed...

That's just a temporary fix. You haven't killed ALL of the algae, they'll be back. You should replace all of your filters and start using an algicide.
I use Biobor JF ...
Forum: Marketplace
04-24-2019, 04:20 PM
Replies: 4
Views: 149
Posted By joeflyer

I've got one NIP. I'm a little reluctant to let...

I've got one NIP. I'm a little reluctant to let it go because I still have a functional DF that I might want to fly some day for old times sake.
I don't remember what I paid for it but the OS...
Forum: RC Jets
04-05-2019, 12:47 PM
Replies: 38
Views: 1,390
Posted By joeflyer

A123's for the Rx 2S Lipo for the ECU

A123's for the Rx
2S Lipo for the ECU
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service