Search: Posts Made By: BobH
Showing results 1 to 18 of 18
Search took 0.07 seconds.
Forum: RC Warbirds and Warplanes 03-19-2017, 07:21 AM
Replies: 10,561
Views: 1,371,220
Posted By BobH
Swamped, last night I had a rational moment...

Swamped, last night I had a rational moment thinking about my build of 20years past. What I actually did was to put the tapes in place and THEN glass the entire wing. There was some filling to do to...
Forum: RC Warbirds and Warplanes 03-18-2017, 04:55 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
The entire wing was sheeted and glassed. The...

The entire wing was sheeted and glassed. The tapes were put on over the glass in the right places simulating rib stations. Once covered this gave the impression of ribs and open bays.
Forum: RC Warbirds and Warplanes 03-18-2017, 12:06 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
I built the 60 Gold Edition years ago. Where the...

I built the 60 Gold Edition years ago. Where the rib stations on the wing were I put down chart tape (real narrow kind) and covered that area with fabric. The rest of the wing was glassed to...
Forum: RC Warbirds and Warplanes 01-05-2017, 07:18 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
I agree.. nice touch with the plug wires :)

I agree.. nice touch with the plug wires :)
Forum: RC Warbirds and Warplanes 01-01-2017, 08:41 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
I doubt that your cowl would get any where near...

I doubt that your cowl would get any where near hot enough to effect the holding power of Neodymium magnets.
Forum: RC Warbirds and Warplanes 12-10-2016, 07:49 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
acdii, the jig centers the hinge between the...

acdii,
the jig centers the hinge between the top and bottom surface. If you have a Gull wing for example.. Each part of the Gull will have its own trailing edge. The jig just centers each section...
Forum: RC Warbirds and Warplanes 12-09-2016, 06:08 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
FYI Robart makes a jig for it's hinge points. It...

FYI Robart makes a jig for it's hinge points. It really helps center the hinge point on the Trailing Edge.
...
Forum: RC Warbirds and Warplanes 07-14-2015, 05:48 AM
Replies: 10,561
Views: 1,371,220
Posted By BobH
I think the only Futaba you can split receivers...

I think the only Futaba you can split receivers on is the newest 18mzh with the new receivers. Check out the Futaba forum for more info.
Forum: RC Warbirds and Warplanes 04-13-2015, 04:28 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
Machine screws and blind nuts.

Machine screws and blind nuts.
Forum: RC Warbirds and Warplanes 03-23-2015, 05:07 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
Just a point about tail weight vs CG. The...

Just a point about tail weight vs CG. The difference is actually the Moment arm length around the CG. So if there is 3X the distance to the CG from the tail vs the Nose to the CG, you need 3X more...
Forum: RC Warbirds and Warplanes 03-04-2015, 07:13 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
Maybe it's your misunderstanding of positive and...

Maybe it's your misunderstanding of positive and negative? any way you look like you have it right :)
Forum: RC Warbirds and Warplanes 03-03-2015, 03:32 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
Steve, you don't want positive degrees of...

Steve, you don't want positive degrees of washout. You want negative degrees. In other words you want the tip pointing downwards relative to the rest of the wing.
Forum: RC Warbirds and Warplanes 04-13-2014, 10:13 AM
Replies: 10,561
Views: 1,371,220
Posted By BobH
The Saito 450 fits in the cowl ok?.. I was...

The Saito 450 fits in the cowl ok?.. I was thinking of the Saito 84 (gas version of the same engine).
Forum: RC Warbirds and Warplanes 01-30-2013, 12:38 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
RE: GROUP BUILD - Top Flite Giant Scale F4U Corsair

I have Seidel/UMS 70 radial. Haven't run it yet but my buddy has run his. They are pretty stingy with the fuel according to him and others with the engine..
Horizon sells the collector ring for a...
Forum: RC Warbirds and Warplanes 01-30-2013, 10:33 AM
Replies: 10,561
Views: 1,371,220
Posted By BobH
RE: GROUP BUILD - Top Flite Giant Scale F4U Corsair

Buy the ring. you'll save yourself lots of aggrivation..
Forum: RC Warbirds and Warplanes 07-23-2010, 09:04 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
RE: GROUP BUILD - Top Flite Giant Scale F4U Corsair

Why are you dividing 48 by anything? Multiply 48X12 that will give you the full scale inches. Then multiply that by the scale factor of your plane. That will give you the scale inches. Or you can...
Forum: RC Warbirds and Warplanes 11-09-2007, 07:38 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
RE: GROUP BUILD - Top Flite Giant Scale F4U Corsair

Depends on what you intend to do with the doors. It really doesn't matter which way you do it. If you intend to use the doors you can glass the entire area and then cut them out.
You might also...
Forum: RC Warbirds and Warplanes 09-27-2007, 05:30 PM
Replies: 10,561
Views: 1,371,220
Posted By BobH
RE: GROUP BUILD - Top Flite Giant Scale F4U Corsair

If you paint the styrene a dark color it may very well warp in the sun. I had that happen to me and ended up pulling it off and replacing it with thin aluminum.. That never warps.
Showing results 1 to 18 of 18



Forum Jump


All times are GMT -8. The time now is 11:23 AM.