Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Gandalv

Page 1 of 4 1 2 3 4

Search: Search took 1.54 seconds.

  1. Replies
    3,276
    Views
    495,852

    RE: Reaction 54 Jet Kit

    Not long after I posted my request for a building instruction, I got the help that I needed :)

    I recived a mail from Bruce and he took care of me.

    Now, thats what I call excellent...
  2. Replies
    3,276
    Views
    495,852

    RE: Reaction 54 Jet Kit

    Need a copy of the building instructions.

    I got back on building my R54, but discovered that I have lost my building instructions [:@] So now I am somewhat stuck

    Is it to be found...
  3. Replies
    77
    Views
    13,294

    RE: Turnigy 1/16 buggy unboxing review

    ESC-help plz.
    The first 3-4 run with my Turnigy buggy everythng was OK, I used 2 cell Lipo on those runs.

    Today I got 4-5 sec run and then ESC goes into "voltage protection" :-s I changed...
  4. Replies
    4,873
    Views
    810,097

    RE: Bob Cat Copy Falcon 120 Jet

    Exelent info in here for the Falcon :) but also a very loooong tread.

    Can someone help me out with this one: It was said someplace in here that the carbontube for an Extra300 or Edge540 would...
  5. Replies
    4,873
    Views
    810,097

    RE: Bob Cat Copy Falcon 120 Jet

    I am soon starting my build on my Falcon v1. This tread is very very nice, but also very long to read. Have someone made a pdf-file with does and dont's on the v1? (like atomix has done on his build...
  6. Replies
    18
    Views
    2,082

    RE: Lanier Ultimate Pitts .91-2.2

    Any of you have the building plans for the ultimate Pitts? I got the kit, but it did not contain any building plans :-(

    Someone that can help me out?

    Thanks.
    Regards from gndalv
  7. Replies
    2
    Views
    382

    Lanier rc, "The Ultimate pitts"

    I found this old kit of the "Ultimate Pitts", ws 60 1/4 inch and recomended engine is .91 - 2.2 2stroke.

    My problem is that I dont have the building plans :(

    Can anyone help me to get a...
  8. Replies
    2
    Views
    463

    RE: Weatronic 2.4 and smaller receivers ?

    Thanks for your reply Michael :)

    I have seen those micro 8ch receivers, but still want smaller. So where wondering if someone knew of something smaller was on Weatronics planning list ;)

    ...
  9. Replies
    2
    Views
    463

    Weatronic 2.4 and smaller receivers ?

    Does anyone know if there will be a smaller receiver in near future for the weatronic 2.4 system ?

    Otherwise Jeti might be a better alternative ? since I got some smaller planes that doesn't...
  10. RE: DIY - Gear / Door sequencer - 18$ and weighs less than 10g !

    nice :)
    thanks for letting us know of this neat little device.
  11. Replies
    26
    Views
    2,787

    RE: Anyone using Hobby King batteries?

    ticketec
    How many C are your batteries for the Wren and 120 ? And how many flights do you get out of those packs ?

    Thanks in advance

    Regards from Gandalv
  12. Replies
    179
    Views
    32,702

    RE: Sterner - DH 100 VAMPIRE buildingThread

    Hello Per

    Was that the silvergray T11 that did that really thight and low 180 degree turn on the north side of Kjevik airport in August/September ? That on almost came right over my rooftop...
  13. Replies
    179
    Views
    32,702

    RE: Sterner - DH 100 VAMPIRE buildingThread

    Hope you get well soon :)

    Here is a question from a novice builder; why is there called for spruce stringers. The fuse is to be planked with 3mm balsa and then glass & epoxy, so would it not be...
  14. Replies
    317
    Views
    28,133

    RE: 2.4 GHz Weatronics, PPM or PCM?

    Maybe of topic and maybe a dumb question, but here goes

    If there is about 1meter from the turbine to the mounting place of the receiver, it seems that the blindspot/shadow behind the turbine...
  15. Replies
    317
    Views
    28,133

    RE: 2.4 GHz Weatronics, PPM or PCM?

    Is the antenna of this unit a directional tx-antenna (since its all flat) ? If so, do you have to point it in the direction of the plane all the time to get the best signal, or is there a round...
  16. Replies
    3,276
    Views
    495,852

    RE: Reaction 54 Jet Kit

    Hello Jim

    That was an interesting and helpfull answer :)

    The strut you are using are 133mm top to bottom and can be used in the Boomer Intro, Dreamworks homepage says. Digitech also have...
  17. Replies
    3,276
    Views
    495,852

    RE: Reaction 54 Jet Kit

    Thanks Bob :-)

    I just sent them a mail. Will let you know the answer, in case someone else are thinking of buying also.

    Regards
  18. Replies
    3,276
    Views
    495,852

    RE: Reaction 54 Jet Kit

    Thanks Bob, that was something I was not aware of, the loaded length was the key.

    Nowthere is just to figure out how much shorter the strut will be when loaded, without having to buy it and...
  19. Replies
    3,276
    Views
    495,852

    RE: Reaction 54 Jet Kit

    Antony, is what I have found in my quest for struts for the Reaction:
    http://shop.digitech-turbines.com/product_info.php?cPath=385_391&products_id=1265&osCsid=0p77f55r2dhcu1iaotekkns8a2

    We...
  20. Replies
    4,873
    Views
    810,097

    RE: Bob Cat Copy Falcon 120 Jet

    Ups, just me being slow [8D]
  21. Replies
    4,873
    Views
    810,097

    RE: Bob Cat Copy Falcon 120 Jet

    Hello BaldEagel

    I see that Pro lynx are adverticing that they make oleos the lenght we want them, so no more too long oleos :)

    heres the link: ...
  22. Replies
    4,873
    Views
    810,097

    RE: Bob Cat Copy Falcon 120 Jet

    Chris

    Where did you get those covers for your servoes ? They vere rather neat :)
  23. Replies
    3,276
    Views
    495,852

    RE: Reaction 54 Jet Kit

    Just got my hands on one of this kits :D and are about to start the build.

    I fly from a VERY bumpy grass-strip, the strip is also used by ultra-light planes and they really put some big holes...
  24. RE: Roamin Research Mig 3, Need a cowl and canopy

    wow F4u5, 120" would make one BIG Mig :)

    Good to hear that the Roamin flies so good. In spite of what has been pointed out of errors and flaws on the Roamin, I have decided to build it (and...
  25. RE: Roamin Research Mig 3, Need a cowl and canopy

    Sent you a pm Evil

    After all its a nice aircraft, so I may build it and try to fix what I can from that you have pointed out :)
Results 1 to 25 of 80
Page 1 of 4 1 2 3 4
All times are GMT -6. The time now is 07:07 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.