Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: w8ye

Page 1 of 40 1 2 3 4

Search: Search took 1.39 seconds.

  1. Replies
    16
    Views
    147

    hook onto the throttle arm and pull out on it?

    hook onto the throttle arm and pull out on it?
  2. Replies
    16
    Views
    147

    All the tool (which is just a rod with threads on...

    All the tool (which is just a rod with threads on the end) does is pull out the throttle barrel. You can use a metric screw to do the same thing or just pullout on the throttle arm?
  3. Replies
    11
    Views
    1,212

    Mintor themselves has apparently faded away? ...

    Mintor themselves has apparently faded away?

    You are going to need to try alternate resources like mentioned above.
  4. Thread: DLE Modifications

    by w8ye
    Replies
    7
    Views
    270

    http://www.rcuniverse.com/forum/gas-engines-142/10...

    http://www.rcuniverse.com/forum/gas-engines-142/10867882-rear-intake-reed-problems.html
  5. Thread: DLE Modifications

    by w8ye
    Replies
    7
    Views
    270

    http://www.rcuniverse.com/forum/tips-techniques-18...

    http://www.rcuniverse.com/forum/tips-techniques-180/11396471-write-up-dle-20-reed-valve-block-mod.html
  6. Thread: DLE Modifications

    by w8ye
    Replies
    7
    Views
    270

    It has been discussed many times before right...

    It has been discussed many times before right here on RC Universe. Do a search?
  7. Send the whole engine to Frank and let him look...

    Send the whole engine to Frank and let him look at it?
  8. Replies
    1
    Views
    99

    Anytime there was more wrong with a carb than...

    Anytime there was more wrong with a carb than replacing the diaphragms, I've been more successful with a different carburetor.
  9. Replies
    28
    Views
    672

    When cold they will sound richer than when warmed...

    When cold they will sound richer than when warmed up.
  10. Replies
    5
    Views
    292

    Most of the Zenoah engines have double ended...

    Most of the Zenoah engines have double ended cranks. These are great from a longevity point of view.

    But if you bump the ground pretty hard with the engine, the impact twists the crankshaft at the...
  11. Replies
    15
    Views
    528

    The Walbro carbs used in Saito gas engines are...

    The Walbro carbs used in Saito gas engines are not listed on the Walbro site either.

    There are several Walbro carbs used on Stihl chainsaws that are only available from Stihl and are not on the...
  12. Replies
    9
    Views
    202

    I just had a bunch of Fox 35 stunts and I never...

    I just had a bunch of Fox 35 stunts and I never had any trouble adjusting the flat end needle valves.
  13. Replies
    28
    Views
    672

    BJ's will definitely tell you the ignition is bad...

    BJ's will definitely tell you the ignition is bad in order to seem more important and jack up the price.

    Someone at BJ's doesn't like the mechanical ignition advance or does not know how to set...
  14. Replies
    33
    Views
    2,263

    I have set up several Fiji water bottle gas...

    I have set up several Fiji water bottle gas tanks. I've always modified a combination of Sullivan and Dubro parts to make the stopper assemblies. They work out very nice and hold up well.

    My...
  15. Replies
    74
    Views
    2,180

    I purchased a beat up G-62 from the Internet that...

    I purchased a beat up G-62 from the Internet that I found to be relatively unused on the inside.

    Cyber Wolf straightened the crank for me. It turned out to be a very nice, like new G-62 with his...
  16. Replies
    28
    Views
    672

    The ignition module that belongs on this engine...

    The ignition module that belongs on this engine does not have electronic advance.

    With the throttle wide open,set the ignition advance at 28 degrees. At idle it should be around 4 degrees. Close...
  17. There are all metal ones from Walbro. The...

    There are all metal ones from Walbro.

    The plastic ones have a serrated brass tube inside and when you try to remove them the plastic breaks off.

    You can get new ones of both styles from Horizon...
  18. Replies
    74
    Views
    2,180

    +1

    +1
  19. Replies
    28
    Views
    672

    If air blows across the breather hole it will...

    If air blows across the breather hole it will sometimes change your mixture for the little hole is a static air pressure reference for the metering valve diaphragm for the demand regulator in the...
  20. Replies
    28
    Views
    672

    The vent tube soldered into the steel cover needs...

    The vent tube soldered into the steel cover needs a piece of fuel line on it and trailed behind the engine preferably inside the fuselage.
  21. Replies
    74
    Views
    2,180

    +1

    +1
  22. Replies
    74
    Views
    2,180

    AFAIK DA will straighten them. Call and ask? ...

    AFAIK DA will straighten them. Call and ask?

    I've had a crank straightened by Cyberwolf

    Antique or Ralph Cunningham also straightens them.

    Locally, there is a guy in Zanesville, Ohio that...
  23. Thread: which is better?

    by w8ye
    Replies
    22
    Views
    782

    At my flying field everyone has at least one DA...

    At my flying field everyone has at least one DA and no one has a Roto.

    There have been some problems with the DA's at times but the factory has always taken care of them.
  24. Replies
    8
    Views
    457

    He was not always Johnny on spot with his Emails...

    He was not always Johnny on spot with his Emails in the past.
  25. Replies
    8
    Views
    172

    Av8tor - very good post

    Av8tor - very good post
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 08:35 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.