Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: 600Bob

Page 1 of 5 1 2 3 4

Search: Search took 0.18 seconds.

  1. Twists in the wings or tail? Check the lateral...

    Twists in the wings or tail? Check the lateral balance to see that it isn't more than just a muffler.
  2. The 30c means the battery is able to deliver a...

    The 30c means the battery is able to deliver a higher max amps if the power system will pull more.

    1300ma x 20c = 26 amps max
    1300ma x 30c = 39 amps max

    Now if your electronic setup can only...
  3. If you need a 3s battery you don't want to use a...

    If you need a 3s battery you don't want to use a 2s to replace it. Here is a 3s 1300mah which would be fine if it fits the battery compartment. They come with different connectors too, I just picked...
  4. Thread: Blade nano qx

    by 600Bob
    Replies
    3
    Views
    255

    Just did some reading, it looks like you need to...

    Just did some reading, it looks like you need to use a switch that controls channel 6. You flip it on then back off to switch modes.
  5. Thread: Blade nano qx

    by 600Bob
    Replies
    3
    Views
    255

    What switch does it show for the Spektrum TX? If...

    What switch does it show for the Spektrum TX? If it's the gear switch it's channel 5 by default.
  6. Replies
    14
    Views
    350

    I had a 17cc in a Thunder Tiger Cloud Dancer...

    I had a 17cc in a Thunder Tiger Cloud Dancer which has a very narrow fuselage and it was a tight fit. Loved that plane but it met it's expiration date :( That engine is now in the 60 size Hangar 9...
  7. Replies
    14
    Views
    350

    You don't have to run a second battery and switch...

    You don't have to run a second battery and switch for the ignition.
  8. If that RX does have failsafe for channels other...

    If that RX does have failsafe for channels other than just the throttle you have to use a different bind procedure.

    Put bind plug into RX. Power up RX. Lights flash. Remove bind plug. Hold TX...
  9. Replies
    6
    Views
    122

    Did you actually create a mix to run both...

    Did you actually create a mix to run both elevator servos? In the DX8 all you need to do is go into the Wing Type menu and for Tail select Dual Elevator. No need to create a mix for it.
  10. Replies
    4
    Views
    764

    Maybe start with a 4 channel like the Blade 120Sr...

    Maybe start with a 4 channel like the Blade 120Sr then move on to collective pitch.
  11. Replies
    4
    Views
    588

    I too am new to quads. The 350QX has new blades...

    I too am new to quads. The 350QX has new blades so broken props shouldn't be an issue. My problem with the quads you listed is the one piece frame, you break one arm and you need a new frame.

    I...
  12. Replies
    11
    Views
    336

    Hangar 9 Taylorcraft. ...

    Hangar 9 Taylorcraft.

    http://www.hangar-9.com/Products/Default.aspx?ProdID=HAN4900
  13. Replies
    3
    Views
    204

    If the wings are straight, not swept, then...

    If the wings are straight, not swept, then measure the cord from the leading edge of the forward wing to the trailing edge of the other wing as if it was a single wing, use 25% of the cord.
  14. Replies
    169
    Views
    16,518

    I use the rigging to hold on the top wings, and I...

    I use the rigging to hold on the top wings, and I take them apart to transport. The rigging doesn't need to be adjusted each time, at least mine doesn't. It does take some time just because of all...
  15. Replies
    169
    Views
    16,518

    RE: ECOMRC TigerMoth 1/4 Scale

    Post 141 on page 6 has a couple of engine mount pictures with the DLE 35RA on my Tiger Moth.
  16. Replies
    21
    Views
    1,113

    RE: taxiing a warbird and taking off

    My reason for comment was that in your original description you only mentioned washout and you seemed to be describing the settings for differential as if it were washout as well. If you had said...
  17. Replies
    21
    Views
    1,113

    RE: taxiing a warbird and taking off

    Washout is a twist in the wing and having both ailerons up slightly above the trailing edge can simulate it. It is used so the wing stalls from the center before the tips.

    Giving the aileron less...
  18. Replies
    169
    Views
    16,518

    RE: ECOMRC TigerMoth 1/4 Scale

    On my Tiger Moth it is 6.5 inches or 165mm from the firewall to the spinner backplate.
  19. Replies
    169
    Views
    16,518

    RE: ECOMRC TigerMoth 1/4 Scale

    I didn't measure the distance in mine,  The standoffs for the DLE 35RA worked out of the box.
  20. Replies
    23
    Views
    1,093

    RE: Charging Lipo Batteries In Transmitter

    I charged it for the first time since the initial charging when I bought the battery.  It took about 19 hrs. to go from 7.3v to full charge, for a 4000mah battery that is a very low c rate.  I...
  21. Replies
    23
    Views
    1,093

    RE: Charging Lipo Batteries In Transmitter

    Actually I wasn't trying to be funny because the Lipo for the TX is made to charge inside the TX. To charge it outside you would have to make a proprietary charge lead like inside the TX. Then I'm...
  22. Replies
    23
    Views
    1,093

    RE: Charging Lipo Batteries In Transmitter

    Perhaps Horizon Hobby should sell a Lipo charging bag big enough to hold the DX8 since you have to charge the Lipo inside the TX?
  23. Replies
    23
    Views
    1,093

    RE: Charging Lipo Batteries In Transmitter

    So are Lipos so unstable that charging at 0.1c is a fire hazard?
  24. Replies
    23
    Views
    1,093

    RE: Charging Lipo Batteries In Transmitter

    Yes I charge mine overnight on a stand near my bed.
  25. RE: Rotoflow fuel tanks by J&L power products

    I also use them in large scale planes.
Results 1 to 25 of 107
Page 1 of 5 1 2 3 4
All times are GMT -6. The time now is 07:30 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.