Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Bax

Page 1 of 40 1 2 3 4

Search: Search took 0.99 seconds.

  1. Replies
    2
    Views
    131

    How are you controlling the function? What...

    How are you controlling the function? What actual function are you using?

    In the Butterfly function, in the Elevator setting section, you can set the curve. I set offset to -50, Rate A to +50...
  2. Thread: Futaba 431

    by Bax
    Replies
    2
    Views
    87

    No. It's intended to be used when you have two...

    No. It's intended to be used when you have two servos operating a given function. You'd use it when you have two aileron servos, one on each aileron, or a similar installation on the elevator...
  3. Replies
    3
    Views
    115

    Futaba only has specs for a 4.8V 4-cell NiCd or...

    Futaba only has specs for a 4.8V 4-cell NiCd or NiMH battery pack. Do not use a 2S lithium battery pack. The servo was designed in 2002, long before higher-voltage battery packs became common.
  4. You are correct. Channel #7 on the S-Bus is THE...

    You are correct. Channel #7 on the S-Bus is THE SAME channel on the PWM pins. They cannot be separated. Channel #7 is channel #7, so matter where it's sourced.


    The R6008SB cannot change what...
  5. Replies
    10
    Views
    917

    That's a beauty!

    That's a beauty!
  6. "Single" means that the particular function's...

    "Single" means that the particular function's settings are for one condition only...the condition where you made it "Single". "Group" means that all conditions set to "Group" share the settings.
    ...
  7. Replies
    3
    Views
    87

    OK, in our transmitter, we set it up this way: ...

    OK, in our transmitter, we set it up this way:

    We set channel 6 to be operated by Switch C (a 3-position switch).

    We turned on the Flaperon mixer and adjusted all of the percentages to +100%,...
  8. Replies
    2
    Views
    65

    Normally, you'd use two channels and mix them so...

    Normally, you'd use two channels and mix them so that you have a rudder->throttle1 mix and a rudder->throttle2 mix. Adjust the mix percentages and directions so that they operate as needed. The...
  9. Replies
    10
    Views
    917

    Just leave the drain open at all times. Route it...

    Just leave the drain open at all times. Route it to vent any oil overboard.
  10. With the 18MZ, you set up a condition. Make it...

    With the 18MZ, you set up a condition. Make it condition #1, so that if you have any other condition in the transmitter active when you turn it on, the transmitter will warn you and not come on...
  11. Replies
    3
    Views
    87

    You use the Flaperon function and set the flap...

    You use the Flaperon function and set the flap channel to be operated by a switch. You use the Flap Trim function to set how much the ailerons move when you move the switch.

    Here's the FAQ:
    ...
  12. Replies
    2
    Views
    140

    A receiver links to one and only one transmitter....

    A receiver links to one and only one transmitter. To use that receiver with a different transmitter means you'll have to link it to the second transmitter. That also means you lose the link to...
  13. Thread: gut feeling

    by Bax
    Replies
    8
    Views
    339

    We're moving this thread to the General Radios...

    We're moving this thread to the General Radios forum. The Tactic Support Forum is for people to ask question of Tactic reps. It is not open for general discussions, nor for anyone to just jump in...
  14. Thread: Futaba's answer

    by Bax
    Replies
    1
    Views
    207

    We're not familiar with the Spektrum servos, so...

    We're not familiar with the Spektrum servos, so we don't know the Futaba equivalent. However, in choosing a servo, the wizard may help:

    http://www.futabarc.com/servos/servo-wizard.php

    Or you...
  15. Thread: BT-32B Fuji engine

    by Bax
    Replies
    2
    Views
    87

    There are zero parts available. Fuji-Invac went...

    There are zero parts available. Fuji-Invac went out of the hobby engine business about a dozen years ago. All support was terminated, all parts gone.
  16. Replies
    1
    Views
    121

    One S-Bus port has ALL channel information. For...

    One S-Bus port has ALL channel information. For multiple servos/decoders, you use hubs and splitters (Y-harness), You can connect as many S-Bus hubs as you need. Just be aware that many connectors...
  17. The S-bus always has EVERY channel operating on...

    The S-bus always has EVERY channel operating on it, even if the receiver has fewer pins for the servos.

    The R6108SB receiver has two modes:

    Mode A--The servo pins are channels 1-8
    Mode B--The...
  18. Replies
    4
    Views
    210

    For the R6008HS receiver, this is from the tech...

    For the R6008HS receiver, this is from the tech notes:

    Power Requirement: 4.8 or 6.0V battery or regulated output from ESC
  19. Replies
    4
    Views
    210

    If you're talking the older receivers on 72 MHz,...

    If you're talking the older receivers on 72 MHz, we'd say no. You will need to regulate them. They were not designed with Lithium battery packs in mind, since they were not in use at all at the...
  20. Replies
    2
    Views
    73

    If the transmitter antenna is damaged, the...

    If the transmitter antenna is damaged, the transmitter must come into the service center for repair. The user is not permitted to effect repairs upon the RF stage of the transmitter, per FCC...
  21. OK, this is not a discussion forum, and...

    OK, this is not a discussion forum, and non-Futaba people should not be answering questions posted here. It looks like the oriiginal poster got his questions answered, so we're closing this thread.
  22. Thread: OS 81FS-a

    by Bax
    Replies
    194
    Views
    17,439

    Normally, you slide the liner up and out, move...

    Normally, you slide the liner up and out, move the piston as far aft as possible and then move the connecting rod as far aft as possible on the wrist pin. You can then work the lower end of the...
  23. Thread: 18SZ Switch Change

    by Bax
    Replies
    2
    Views
    155

    These are what you need: HSP79113 TFT1200921...

    These are what you need:

    HSP79113 TFT1200921 TA86 PCB ASSY 3TF10 US$11.20 (short toggle)
    HSP79115 TFT1200922 TA86 PCB ASSY 3TFL1 US$15.32 (long toggle)

    These parts can be...
  24. Thread: wise gyro

    by Bax
    Replies
    2
    Views
    79

    There's no reason at all to not use the WISE...

    There's no reason at all to not use the WISE system in other aircraft. You just need to connect it up and then do the setup per the instructions.
  25. You can always use a tuned exhaust system. ...

    You can always use a tuned exhaust system. Properly-installed, they make the engine run more efficiently and can even reduce sound levels.
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
RCU Reviews
All times are GMT -6. The time now is 01:01 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.