Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: perhamrocks

Page 1 of 23 1 2 3 4

Search: Search took 0.83 seconds.

  1. Replies
    5
    Views
    558

    RE: Volcano 2 speed trans....

    yes you can, but i would suggest you get a direct drive tranny with the 13 tooth clutchbell, this can be purchased as a set from somewhere, i think rufaster might have it. it will give u both better...
  2. Replies
    6
    Views
    544

    RE: Landslide Engineering Requests

    yup thats is true, good point</p>

    </p>
  3. Replies
    6
    Views
    544

    RE: Landslide Engineering Requests

    thicker alluminum shock towers on the landslide if that hasnt already been fixed cause i know that was fixed for the 21 series
  4. Replies
    4
    Views
    397

    RE: Video's of Jump contest Winner!!

    landlide, and landslide 21
  5. Replies
    4
    Views
    397

    RE: Video's of Jump contest Winner!!

    if u just want to see the vids check out youtube. i have won 2 contests just check out perhamrocks on youtube</p>
  6. Replies
    7
    Views
    593

    RE: support for vortex ss??

    its so new that their just arent any vids out there yet
  7. RE: Volcano SV - Default Factory Settings

    make sure u turn the high speed needle back out 2 1/2 turns after u turn it all the way down.
    i know thats what u ment to say chevy
  8. Replies
    28
    Views
    2,224

    RE: Sh .18 not working

    check to make sure all of the needles are set to factory settings, if they r, maybe try leanin the low speed a little bit, cause it sounds like you have everything else set up properly
  9. Replies
    3
    Views
    406

    RE: broken drive shaft

    ya i did that to my volcano too, but&#160;that was because i was only running rear wheel drive cause i lost a dogbone
  10. Replies
    4
    Views
    353

    RE: landslide front hub

    i believe there is a grub screw inside of there that u have to take out
  11. Replies
    0
    Views
    238

    Aftershock Parts?

    do you have them in yet? i know most of them are probably interchangable with the landslide, but i think i'd like to buy some aftershock tires for my landslide.
  12. Replies
    6
    Views
    468

    RE: spur gear

    cut a piece of paper to width so it can be slid between the spur gear and clutchbell, loosen all of the motor mount screws on the underside of the chasis and slide the push the engine over tight...
  13. Replies
    6
    Views
    468

    RE: spur gear

    yup, exactly what firebird said.
  14. Replies
    5
    Views
    472

    RE: traxxas 3.3

    check out sh engines, they have some really nice .21's, you can get the sh .21 p3 from redcat in the engine replacement program for somwhere around $60 i'm guessing, but i don't think the p3 is going...
  15. Replies
    7
    Views
    633

    RE: 3.2 tires

    might want to upgrade to thicker drive shafts and drive cups too cause the big wheels and the bigger engine is going to put lots of stress on that drive train, but you can sure try it
  16. Replies
    6
    Views
    561

    RE: Sh 18 Rotostart

    it sounds like ur engine is just flooded and ur drill doesnt have enough power to turn it over
  17. Replies
    7
    Views
    633

    RE: 3.2 tires

    engine will bog down to from the large tires
  18. Replies
    4
    Views
    530

    RE: t-maxx shock mod

    hope this helps
  19. Replies
    11
    Views
    541

    RE: new wheels

    didn't he turn one into an all out tsunami utrawide too pede?
  20. Replies
    11
    Views
    541

    RE: new wheels

    i remember i while back some guy converted his buggy into an ultrawide and i think he figured it cost him about $600 after he was all done
  21. Replies
    11
    Views
    541

    RE: new wheels

    if it has the two speed yes you'll need a new setup, maybe the direct drive package would be good.
    if it is a single speed, it probably would just need a different clutchbell
  22. Replies
    3
    Views
    435

    RE: yeah! new shocks

    they will just snap on if u use the spacers provided and if u have long enough screws, but u will have to sand down the reciever box where the screw holds it down and place a bolt through the end of...
  23. Replies
    14
    Views
    856

    RE: Jumped Landslide, need help!!!!

    all u need is the rear lower hinge pin, which is part #60072
    just search for that part number on the redcat site, or any other redcat dealer's site
    the part u need is what u called the "tony...
  24. Thread: help?

    by perhamrocks
    Replies
    3
    Views
    276

    RE: help?

    sounds like ur low speed needle is too rich. lean it out and that should also help ur idle along with the idle screw
  25. Replies
    8
    Views
    413

    RE: actual temp?

    200 - 215 is probably right for the idle temp after then engine has been warmed up, but it should be around 260 at it's top rpm's
Results 1 to 25 of 553
Page 1 of 23 1 2 3 4
All times are GMT -6. The time now is 10:06 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.