Search: Posts Made By: George
Showing results 1 to 25 of 500
Search took 0.79 seconds.
Forum: RC Jets 02-04-2018, 03:01 PM
Replies: 13
Views: 796
Posted By George
I built/assembled an Avanti S at KY Jets a couple...

I built/assembled an Avanti S at KY Jets a couple years ago during the rain-fest. I started on Tues. and did the maiden Fri. evening. It's great flying airplane as I'm sure the T1 is as well, I just...
Forum: JetCat Turbine Direct Support 01-31-2018, 08:32 PM
Replies: 5
Views: 177
Posted By George
Post a video of the GSU screen showing the entire...

Post a video of the GSU screen showing the entire boot-up.
Forum: RC Jets 01-12-2018, 05:47 AM
Replies: 16
Views: 1,081
Posted By George
321-412-3078

321-412-3078
Forum: Futaba Radios Direct support forum 01-04-2018, 08:21 AM
Replies: 2
Views: 220
Posted By George
Thanks Bill!

Thanks Bill!
Forum: Futaba Radios Direct support forum 01-04-2018, 05:05 AM
Replies: 4
Views: 237
Posted By George
PM Sent

PM Sent
Forum: Futaba Radios Direct support forum 01-03-2018, 07:43 PM
Replies: 4
Views: 237
Posted By George
Yes, it's the 18SZ Model Data Converter Ver....

Yes, it's the 18SZ Model Data Converter Ver. 2.2.0 located at https://www.futabarc.com/software-updates.html

I just used it to convert models from 18MZ to a 18SZ.
Forum: Futaba Radios Direct support forum 01-03-2018, 02:51 PM
Replies: 2
Views: 220
Posted By George
Repair Warranty

What is the warranty for a repaired radio (18MZ)?

My radio is currently at the service center. I received the repair estimate today (Main PCB Assembly - $1200). I called to find out what the...
Forum: RC Jets 10-13-2017, 04:49 AM
Replies: 18
Views: 1,698
Posted By George
The Future of Dreamworks Model Products

To the Loyal Patrons, Vendors, and Business Partners of Dreamworks Model Products,

Many of you have reached out to us recently, wondering what is going to happen with our business and that of...
Forum: Dreamworks Model Products 10-13-2017, 04:44 AM
Replies: 6
Views: 1,110
Posted By George
Dreamworks Model Products LLC...

Dreamworks Model Products LLC (http://www.dreamworksrc.com/catalog/Dreamworks-Ventrix-Sport-Jet-Combo)
Forum: RC Jets 01-24-2017, 03:05 PM
Replies: 78
Views: 9,041
Posted By George
Glad I could help Danny, but that the V2 should...

Glad I could help Danny, but that the V2 should be a piece of cake for you!! :cool:
Forum: RC Jets 01-24-2017, 04:34 AM
Replies: 78
Views: 9,041
Posted By George
I melted the lead in a spoon and poured it into...

I melted the lead in a spoon and poured it into the holes I bored.
Forum: RC Jets 12-17-2016, 12:44 PM
Replies: 78
Views: 9,041
Posted By George
Without changing anything from the stock...

Without changing anything from the stock position, the plane will want to climb at full throttle...if you trim for this setting (down elevator trim), when you come off the power, the plane will want...
Forum: RC Jets 12-17-2016, 10:18 AM
Replies: 78
Views: 9,041
Posted By George
It makes the plane less "pitch-sensitive" to...

It makes the plane less "pitch-sensitive" to throttle position (thrust).
Forum: RC Jets 12-02-2016, 06:38 PM
Replies: 3
Views: 812
Posted By George
Definitely, a really good movie!!

Definitely, a really good movie!!
Forum: RC Jets 11-07-2016, 06:57 AM
Replies: 78
Views: 9,041
Posted By George
I did the maiden at FJ in the worst possible...

I did the maiden at FJ in the worst possible conditions, so I really didn't get a chance to get things trimmed and set-up properly.

I'm for Fentress to open up again so I can get some flights in.
Forum: JetCat Turbine Direct Support 11-04-2016, 09:08 AM
Replies: 4
Views: 482
Posted By George
Both are in the same parameter screen.

Both are in the same parameter screen.
Forum: JetCat Turbine Direct Support 11-04-2016, 09:00 AM
Replies: 4
Views: 482
Posted By George
Press Limits button...scroll to Maximum...

Press Limits button...scroll to Maximum RPM...lower value by pressing AND holding the Change Value button and pressing the left arrow (-) button until you reach the RPM and corresponding Newton value...
Forum: JetCat Turbine Direct Support 11-04-2016, 08:54 AM
Replies: 4
Views: 569
Posted By George
Try lowering U1 a couple points....(press Limits...

Try lowering U1 a couple points....(press Limits button once, then press AND hold Limits button and press right arrow (+) button, U1 parameter should now be visible (if not, press right arrow (+)...
Forum: RC Jets 11-02-2016, 08:46 PM
Replies: 175
Views: 18,267
Posted By George
Thanks Danny!!

Thanks Danny!!
Forum: RC Jets 11-01-2016, 06:42 PM
Replies: 175
Views: 18,267
Posted By George
Does anyone have the file for the Xicoy Balancer?

Does anyone have the file for the Xicoy Balancer?
Forum: JetCat Turbine Direct Support 10-30-2016, 04:10 PM
Replies: 4
Views: 569
Posted By George
What is the error message?

What is the error message?
Forum: RC Jets 10-07-2016, 11:50 AM
Replies: 6
Views: 1,553
Posted By George
+3

+3
Forum: RC Jets 10-04-2016, 03:53 AM
Replies: 189
Views: 30,725
Posted By George
It's been a very long time Greg, glad to see you...

It's been a very long time Greg, glad to see you are still at it. I always liked that plane, too bad it was never produced. :(
Forum: RC Jets 10-02-2016, 07:02 AM
Replies: 22
Views: 1,091
Posted By George
This appears to be the shutdown data. The last...

This appears to be the shutdown data. The last data line (anomaly) is actually the first data line of the set, but for some reason, it always ends up at the bottom of the data. If you were to...
Forum: RC Jets 08-29-2016, 10:42 AM
Replies: 12
Views: 2,085
Posted By George
This will be my only post on this matter, but...

This will be my only post on this matter, but Thud has pretty much nailed it.

Regarding the OP, the matter has been settled after I conferred with the factory.

On a side note, I appreciate the...
Showing results 1 to 25 of 500



Forum Jump


All times are GMT -8. The time now is 07:26 AM.