Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: cadillac98

Page 1 of 3 1 2 3

Search: Search took 0.55 seconds.

  1. RE: i gotta b close to ideal..please help

    ok
  2. i gotta b close to ideal..please help

    i recently tried to tune my landslide again from the factory settings...i finally got a strong idle and pretty good acceleration, but when i apply the brakes after full throttle it immediately...
  3. Replies
    14
    Views
    857

    RE: Jumped Landslide, need help!!!!

    the hinge pin may not be going in because something around it is bent..ive had to replace one on my landslide..make sure nothing is bent and try to put the pin in..i wouldnt be surprised if the tip...
  4. Replies
    17
    Views
    1,928

    RE: y are my glow plugs going out so fast?

    how much needs to be takin off to get a good cleaning job done inside
  5. Replies
    4
    Views
    426

    RE: sh18 head button

    ok...so how much do i need to remove from the engine in order to rinse it out..i have the cooling head and exhaust off of it now
  6. Replies
    9
    Views
    479

    RE: what is a head button???

    ok..thanks
  7. Replies
    17
    Views
    1,928

    RE: y are my glow plugs going out so fast?

    well i had to remove the cooling head to replace the head button..i guess this would be an ideal time to take the engine apart and clean the insides, especially since i stripped the head button...im...
  8. Replies
    9
    Views
    479

    RE: what is a head button???

    i was thinking about that too...i have the sh18..is it difficult to get inside it to rinse it out? do i use water?
  9. Replies
    9
    Views
    479

    what is a head button???

    just wanna make sure this is what i need b4 i order it..i was tightening down my glow plug and went too far..i stripped sumthing...i bought a new plug and it didnt tighten either..after removing the...
  10. Replies
    4
    Views
    426

    sh18 head button

    just wanna make sure this is what i need b4 i order it..i was tightening down my glow plug and went too far..i stripped sumthing...i bought a new plug and it didnt tighten either..after removing the...
  11. Replies
    17
    Views
    1,928

    RE: y are my glow plugs going out so fast?

    i got a couple from hobby town and a couple from rufaster...i know two were os brand...but as long as there is smoke coming from the pipe i should be ok right..i mean i tune it where its not too much...
  12. Replies
    17
    Views
    1,928

    RE: y are my glow plugs going out so fast?

    is there anything else u guys can think of that would cause the plugs to be going out so quick..i mean i had to change two today..they were medium tho, but still..i have used plugs for much longer...
  13. Replies
    17
    Views
    1,928

    RE: y are my glow plugs going out so fast?

    exactly..goes dead and i check the plug by taking it out and touching it to the ignitor..no light, not good
  14. Replies
    17
    Views
    1,928

    RE: y are my glow plugs going out so fast?

    should i be using cold med or hot plugs since im using 20% nitro?
  15. Replies
    17
    Views
    1,928

    RE: y are my glow plugs going out so fast?

    im using the premium fuel..its 20% nitro...and the last 3 plugs i went thru were medium...jus ordered two cold and 1 medium..i know my hsn is not too lean because there is a good amount of smoke...
  16. Replies
    17
    Views
    1,928

    y are my glow plugs going out so fast?

    i dont think im running it too lean or anything...but it seems to go thru a glow plug after each rday of running now, sometimes going thur two in a day..it didnt used to be like this...what could be...
  17. RE: please tell me where the shift adjust screw is

    u mean where the two holes are in the gear box?
  18. please tell me where the shift adjust screw is

    i have the landslide 1/8 and i noticed it shifting very early..i have read before about adjusting a screw and making it shift earlier or later...can someone please explain what and exactly where this...
  19. please explain what to adjust to make shift later?

    i have the landslide 1/8 and i noticed it shifting very early..i have read before about adjusting a screw and making it shift earlier or later...can someone please explain what and exactly where...
  20. RE: has anyone upgraded the center dogbones on landslide??

    no u didnt confuse me..because i have done that already to remove the REAR DOGBONES (side)..i was asking about the center drive cups that the center bones go into...didnt have to take apart the gear...
  21. RE: has anyone upgraded the center dogbones on landslide??

    i have went thru a few sets of rear dogbones, jus snapped during run...i upgraded those, now the center dogbone snapped..im about to upgrade this and the center drive cups etc..these ultralites are...
  22. has anyone upgraded the center dogbones on landslide??

    i have the 1/8 landslide ....im tryna figure out if i need to take the whole diff gear box apart to change the center driven joint cup..i took it apart once to upgrade the rear dogbones...there is a...
  23. Replies
    1
    Views
    411

    how does a damaged flywheel look?

    how does a damaged flywheel look?
  24. Replies
    5
    Views
    766

    car rotors..drilled?slotted?

    what are the advantages of drilled/slotted rotors over rotors that are jus drilled?
  25. Replies
    10
    Views
    565

    RE: flywheel is too loose...

    the clutch shoes need to be removed also right? in order to tighten up the flywheel
Results 1 to 25 of 70
Page 1 of 3 1 2 3
All times are GMT -6. The time now is 12:21 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.