Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: KC36330

Page 1 of 40 1 2 3 4

Search: Search took 0.80 seconds.

  1. Replies
    47
    Views
    1,879

    did i say that power loss to the pump wouldn't...

    did i say that power loss to the pump wouldn't stop the turbine?

    the question asked was what is the purpose of the solenoid, so once again, the solenoid provides a means of immediately...
  2. Replies
    47
    Views
    1,879

    the solenoid provides a means of immediately...

    the solenoid provides a means of immediately stopping fuel flow to the turbine. shutting off the power to the fuel pump doesn't immediately stop the flow of fuel.
  3. Replies
    4
    Views
    240

    I'll FTP it to a temp server and send you a link...

    I'll FTP it to a temp server and send you a link via PM and if you could do the 'Dropbox' and post it here i'll delete it from the temp server when you finish. it's V1.01

    2106575
  4. Replies
    1,524
    Views
    146,031

    I never stopped, just all the drama queens at the...

    I never stopped, just all the drama queens at the local fields we are selective when/where we fly.
  5. Replies
    1,524
    Views
    146,031

    Paul, i had ordered a break hub from GJC but it...

    Paul, i had ordered a break hub from GJC but it turned out to be the wrong size, i managed to get the old hub machined and a new air nipple installed last night so i just need some scissor link...
  6. Replies
    1,524
    Views
    146,031

    Due to accidental bumping of the gear switch on...

    Due to accidental bumping of the gear switch on take off roll i'm in need of a few landing gear parts if any one has any they want to part with let me know.
  7. Replies
    2
    Views
    311

    http://us7.campaign-archive1.com/?u=5ec0d287fe154c...

    http://us7.campaign-archive1.com/?u=5ec0d287fe154cc8789afc876&id=19c5bd42f1&e=8529631c6b
  8. Replies
    5
    Views
    639

    if all you need is an o-ring kit, you can make...

    if all you need is an o-ring kit, you can make your own (that's what i did) by trimming some silicone fuel tubing to appropriate size.
  9. Spektrum VR6007

    Spektrum VR6007
  10. there are 4 current waiver holders in your posted...

    there are 4 current waiver holders in your posted location (Tulsa, OK), i'm sure you could get them to work with you on getting prepared for the waiver flight.
  11. Replies
    2
    Views
    310

    there is no safe low voltage monitoring for LiFe...

    there is no safe low voltage monitoring for LiFe batteries due to heir flat discharge curve, i log my voltages in flight and they don't change much at all between fully charged and DEAD, you just...
  12. Replies
    12
    Views
    553

    A 0000μs reading sounds like the throttle male to...

    A 0000μs reading sounds like the throttle male to male lead is plunged in backwards and the ground is going to the signal.
  13. Thread: fuel in tanks

    by KC36330
    Replies
    17
    Views
    1,026

    Harley it's the UV light reacting with the...

    Harley it's the UV light reacting with the turbine oil that causes the discoloration of the tank/lines that's why where the BVM sticker was blocking the light before it fell off is a different color.
  14. Replies
    12
    Views
    1,031

    RE: Surging on Acceleration (again)

    No, it only resets the PID loops. Atmospheric conditions (determined with algorithms during previous runs) are stored and used by the ECU, sometimes when the turbine has sat unused this algorithm can...
  15. Replies
    12
    Views
    1,031

    RE: Surging on Acceleration (again)

    Hold Manual on the GSU and slowly advance thrust while continuing to hold it down and continue holding about 30 seconds. It will reset the PID loops and should clear up the issue.
  16. Replies
    21
    Views
    1,679

    RE: Can't learn Rc

    Binding at 150% and doing the Learn RC at 75% gives higher resolution then the 100/50.
  17. Replies
    20
    Views
    2,248

    RE: Tamjets Servo Mounts

    that's been my experience with them as well, i use CA in the center to hold them down while the epoxy/hysol around the outer edges dries. can't even rip them off to reuse them later without...
  18. Replies
    21
    Views
    1,679

    RE: Can't learn Rc

    See if you can do the Learn RC with the button on the IO board.
  19. Replies
    21
    Views
    1,679

    RE: Can't learn Rc

    Does the value on the GSU change if you move the throttle stick?
  20. Thread: Powerfail

    by KC36330
    Replies
    5
    Views
    580

    RE: Powerfail

    power fail is loss of power from the receiver.
  21. Replies
    21
    Views
    1,679

    RE: Can't learn Rc

    yes it is, you bind for failsafe with 150%, reduce to 75% and learn RC works perfect.
  22. RE: C-ARF Flash Build Thread for All Flash's being built this winter

    looks good!!
  23. RE: C-ARF Flash Build Thread for All Flash's being built this winter

    the pic's were of Douggy's old classic flash and my classic flash, they are just Velcro'd in, it works great. the wing holds them in place in flight and the Velcro when the wing is off.
  24. Replies
    71
    Views
    4,236

    RE: Info from Data Terminal after a shutdown

    the FADEC monitors your requested RPM and it does it's part to get the turbine to match that, the acceleration/deceleration parameters determine how quickly it's allowed to do that, the rapid back...
  25. Replies
    71
    Views
    4,236

    RE: Info from Data Terminal after a shutdown

    the video shows no fault of the turbine, it runs fine up till you start jamming the throttle stick up and down to induce a fault (the pump can't possibly keep up with your up/down/up/down demands),...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 11:24 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.