Notices
 
Search: Posts Made By: digout
Showing results 1 to 25 of 86
Search took 0.60 seconds.
07-13-2016, 01:55 PM
Replies: 2,053
Views: 203,873
Posted By digout

Finally, metal gears for the Chaos! I found...

Finally, metal gears for the Chaos! I found that the Basher 1/16 Mini Nitro Circus sealed high performance metal diffs will fit into the Chaos diff housing. Using the Chaos size bearing, some...
Forum: CEN Racing
06-23-2010, 11:11 AM
Replies: 10
Views: 1,863
Posted By digout

RE: savage tranny in a GST

toez71,
Good work! How does it run with the Savage tranny? I am pondering on whether or not to do this to my GSR 5.0. What center drive shafts will work?
Forum: CEN Racing
04-12-2010, 09:59 PM
Replies: 7
Views: 1,547
Posted By digout

RE: Cen FF

Dr Honda.. I have a FF and am interested in your shock towers. I sent you a PM.
02-23-2009, 06:21 PM
Replies: 1,206
Views: 98,284
Posted By digout

RE: Anyone Have a Mini MGT?

The TRX 3.3 was fairly fast and controllable. No vids yet. I was looking for really fast so i put in a big block OS 21. Now the speeds are up there like my Jato. Probably going to need spare...
02-17-2009, 10:03 PM
Replies: 1,206
Views: 98,284
Posted By digout

RE: Anyone Have a Mini MGT?

Here are some pictures showing how I installed the Traxxas 3.3. To install this engine I used a Dynamite exhaust pipe/manifold from a TMax and set up the carb linkage for a slide.
02-07-2009, 10:39 PM
Replies: 2,328
Views: 214,345
Posted By digout

RE: Tower Hobbies Nitro TOWER Terror MT .25 RTR

There is no kit. I had to buy ($68) a used trinity Nitro Spyder off of E-Bay for the parts. Since the Terror and Spyder were both made by Flying Point, all parts interchanged except the 2speed. ...
02-07-2009, 08:18 PM
Replies: 1,206
Views: 98,284
Posted By digout

RE: Anyone Have a Mini MGT?

The Traxxas 3.3 will fit right in the MGT. I have one in mine. The changes needed are install a long rod to push the carb open, remove all carb rotating stuff on the MGT and add a Dynmite exhaust...
02-07-2009, 08:03 PM
Replies: 2,328
Views: 214,345
Posted By digout

02-07-2009, 10:33 AM
Replies: 2,328
Views: 214,345
Posted By digout

RE: Tower Hobbies Nitro TOWER Terror MT .25 RTR

Has anybody tried the Tower Terror to Trinity Nitro Spyder conversion. I have been running mine for a few months and find that this conversion gives one all the things that the Terror needed as...
07-26-2008, 04:05 PM
Replies: 2,328
Views: 214,345
Posted By digout

RE: Tower Hobbies Nitro TOWER Terror MT .25 RTR

I just recently purchased a used Trinity Spyder. Has any body noticed that the Spyder is almost the same truck as the Tower Terror (TT)? It has an internal steel two speed transmission, reverse,...
Forum: CEN Racing
03-23-2008, 01:26 PM
Replies: 46
Views: 16,051
Posted By digout

RE: CEN MG16 Exhaust Fix

The pede pipe was a disappointment. The manifold was too restrictive. Muck76 found that if you make the stock oToyz forum for complete details.
Forum: CEN Racing
02-27-2008, 08:17 PM
Replies: 5
Views: 881
Posted By digout

RE: mg10 engine upgrade

My HPI Firestorm engine fitted into the CEN MG10 with a little work. It would be nice if we could get ahold of some of CEN's slide carbs that would fit the CEN .18 from the Magnums.
These...
02-27-2008, 08:11 PM
Replies: 6,618
Views: 627,210
Posted By digout

RE: -=OFFICIAL HPI FIRESTORM THREAD=-

I have upgraded my Firestorm with a Traxxas 3.3 engine. Yes, I did have to use wheelie bars! I put the HPI engine in a CEN MG10 and now it also goes faster.
02-22-2008, 03:53 PM
Replies: 36
Views: 2,694
Posted By digout

RE: engine upgrade for mg16?

I am still running my MG16 with the team orion .18 side exhaust/slide carb. I just finished Muck76's dual exhaust mod except I JB welded everything thing together eliminating the long interior...
12-31-2007, 06:19 PM
Replies: 2,053
Views: 203,873
Posted By digout

RE: SPORTWERKS chaos 1/16 buggy

I have a Chaos, VTX and a Next. The Vulcan uses the same diffs as the VTX and Next. Comparing this diff to the Chaos it is all together different. I agree the Chaos needs a metal diff for us...
10-26-2007, 06:24 PM
Replies: 2,328
Views: 214,345
Posted By digout

RE: Tower Hobbies Nitro TOWER Terror MT .25 RTR

You need Ofna part number 30051. They are a 17mm conversion. I have been running them on my TT for several months with them. They are a direct fit with no mods required.
10-13-2007, 10:19 AM
Replies: 90
Views: 8,229
Posted By digout

RE: Opinions on CEN MG16??

My MG16 runs fairly strong now that I have upgraded it with a .18 engine. Thanks to muck76 in finding the CEN MG095 flywheel so that now we can use .18 engines. I have installed a Team Orion...
Forum: CEN Racing
09-30-2007, 08:50 PM
Replies: 53
Views: 6,013
Posted By digout

RE: cen magnum nc clutch bell with gears.

HPI makes a steel 2-speed clutch bell that a few have tried. It is part number A820 and A823 (11/14 and 13/16). Most people would keep the same number of teeth apart on clutch bell and spur gear 2...
09-20-2007, 09:03 PM
Replies: 39
Views: 3,853
Posted By digout

RE: Cen MG 16

Mine leaked a lot from the muffler housing. The CEN manufacturer had not installed any gaskets in the muffler housing. That was the first reason I changed it out to another muffler type. The...
09-18-2007, 09:31 PM
Replies: 39
Views: 3,853
Posted By digout

RE: Cen MG 16

Muck76 that is correct that I used a TT flywheel, 3 shoe clutch and 13 tooth bell to install the HPI 3.0 engine. I also installed a OS slide carb on the HPI engine for linkage fit. I believe that...
09-17-2007, 05:29 PM
Replies: 39
Views: 3,853
Posted By digout

RE: Cen MG 16

Changing to the roller bearings improved the MG16 quite a bit. I have completed the installation of the HPI 3.0 .18 engine. Now the truck has some real speed. The only engine I found that...
Forum: CEN Racing
09-10-2007, 10:03 PM
Replies: 36
Views: 3,088
Posted By digout

RE: How old?

Never stopped playing with toys that made noise ....58.



CEN Magnum | CEN MT2 | CEN MG10 TR | CEN MG16 | Titan | Dominator | CRT.5
Forum: CEN Racing
09-07-2007, 09:36 PM
Replies: 2
Views: 807
Posted By digout

RE: MG10 Camber Rods and Larger Fuel Tank

I also found that the adjustable CEN MT2 truck rear camber rods work great for the MG10 steering rods to give full adjustability.
Forum: CEN Racing
09-07-2007, 06:44 PM
Replies: 2
Views: 807
Posted By digout

MG10 Camber Rods and Larger Fuel Tank

An easy upgrade for the fixed MG10 TR front/rear camber rods is to add the front Traxxas Jato camber and steering rods. They are a direct fit. I was wearing out tires too fast with the original...
Forum: CEN Racing
09-03-2007, 10:49 AM
Replies: 7
Views: 990
Posted By digout

RE: MG10???

I find that the MG10 TR is a great truck! So is the MG16! I went on ahead and made it faster by adding an HPI Firestorm .18 engine onto it. I had to use a Tower Terror flywheel, and clutch bell...
Showing results 1 to 25 of 86
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.