Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: All Day Dan

Page 1 of 40 1 2 3 4

Search: Search took 0.89 seconds.

  1. Replies
    0
    Views
    49

    Stopped Receiving Posts

    I stopped receiving posts to the forums I am subscribed to. What happened? How do I start getting them? Dan.
  2. The plans and instructions were delivered to an...

    The plans and instructions were delivered to an alternate address. Your neighbor's perhaps? Dan.
  3. Replies
    17
    Views
    265

    This will help. Dan. ...

    This will help. Dan.

    http://www.mnbigbirds.com/Servo%20Torque%20Caculator.htm
  4. Replies
    9
    Views
    490

    The starting problems with my three active Brison...

    The starting problems with my three active Brison 3.2s have been solved. It turns out that I had the low speed needle valve much too lean. I was able turn it out 1/16 of a turn or more and the...
  5. Thanks Matt. It's my own design. Dan.

    Thanks Matt. It's my own design. Dan.
  6. Those end pieces on the meter do not engage the...

    Those end pieces on the meter do not engage the leading and trailing edges of the airfoil the same for a symmetrical airfoil as a non-symmetrical airfoil the same way You can see the difference in...
  7. I use the Robart meter all the time. Keep in mind...

    I use the Robart meter all the time. Keep in mind that the original Astro Hog did not have a symmetrical airfoil. It may have been a NACA 2415. If Sig has continued with that it will effect the...
  8. Replies
    9
    Views
    264

    Should be a great project. I've been using the...

    Should be a great project. I've been using the Spring Air retracts for years with absolute success. See if they have anything that fits your design. Dan.

    http://retracts.com/
  9. You can see that the front of the hull has to be...

    You can see that the front of the hull has to be modified to match the deck. It's in the DVD. The plans were dropped off at the post office this AM. Dan.
  10. Yes it is. Dan.2110199

    Yes it is. Dan.2110199
  11. I'm having some trouble with RCU. I got your...

    I'm having some trouble with RCU. I got your address and I'll send the information during the week. Which version are you building? Dan.


    21099772109978
  12. OK. I didn't know you had the servos. You're a...

    OK. I didn't know you had the servos. You're a little long on the unsupported ends. Here's how I do it. Dan.


    210997221099742109975
  13. I have them. PM me your address and I'll send...

    I have them. PM me your address and I'll send them to you. You can copy what you need an send them back. Dan.
  14. Tim, usually you have the radio first and design...

    Tim, usually you have the radio first and design the radio installation into the model during the build. This includes the pushrods, servo mounts receiver and battery location. Each moving surface...
  15. Replies
    5
    Views
    162

    RJ, what engine are you talking about and which...

    RJ, what engine are you talking about and which carburetor does it have? Dan.
  16. You need some gussets in the four corners to...

    You need some gussets in the four corners to strengthen the wing mount. Here's what I did in a 50cc Tripacer. Dan.


    21093592109360
  17. Replies
    4
    Views
    136

    Use the above diagram. There are enough alignment...

    Use the above diagram. There are enough alignment tabs in the diaphragms to make sure they go in right. Make sure the one on the side with the four mounting screw goes against the cover, not the body...
  18. Peak Charging Versus Constant Current Charging

    I am constantly getting more capacity out of my NiCad and NiMH packs when I use a constant current charger instead of my peak charger. I am charging them at one tenth their rated capacity. Even with...
  19. Replies
    9
    Views
    490

    I had one of the engines out this week and got...

    I had one of the engines out this week and got ten good starts. The five cell battery pack from NOBS was installed. I richened the low speed needle valve a bit, put the prop at the 3 o’clock position...
  20. Replies
    12
    Views
    333

    Lou, sign me up for one of the books. I used to...

    Lou, sign me up for one of the books. I used to be king of the control line circles in Riis Park, yes the one in Queens, from the late 40s to the early 50s. We used to fly in the parking lot or on...
  21. Replies
    12
    Views
    333

    Lou, what a great post!. It's just what I was...

    Lou, what a great post!. It's just what I was looking for. That book is still available if you have nothing better to do with a $100. Dan.
    ...
  22. Replies
    12
    Views
    333

    Good posts. I have found advertisements for the...

    Good posts. I have found advertisements for the U-reely and Firebaby in the 1950 issues of MAN. I didn’t have time to check the 49s. He may have advertised in the earlier issues of Air Trails. I...
  23. Replies
    12
    Views
    333

    Thanks Gizmo, Here's me with a Barnstormer around...

    Thanks Gizmo, Here's me with a Barnstormer around 1953. That was many years after I started with the Firebaby. Used the Ureely with the Testers Freshman, Zilch, Sterling profiles and many others....
  24. Replies
    12
    Views
    333

    Jim Walker Firebaby and U-Reely

    What years were the Jim Walker Firebaby and U-Reely released? Thank. Dan.
  25. Replies
    2
    Views
    106

    You can get CH ignitions from Bill Jensen or...

    You can get CH ignitions from Bill Jensen or RCXps from Milton Thompson at rcextreme.com. Dan.
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 10:26 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.