Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Undetermined

Search: Search took 0.53 seconds.

  1. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    It's been a while since I have messed with my Tornado. I also have a Tsunami I bought off a buddy with the same problem.<div>
    </div><div>Transmissions keep stripping. Not sure why, I have been...
  2. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    Are these alright servos? I would like to get some high end ones, but honestly I am going to tear it up. I do jumps and flips, etc. Would like something decent and budget friendly.
    ...
  3. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    Any ideas on how to keep the gas tank from letting air into the lines? When my tank gets below about 1/2 tank, and I hit some little bumps, my car gets a lot of air in the lines and chokes out. Was...
  4. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    I would highly recommend against blowing into the tank. I emptied it and pulled the lines. However, there was a small amount that did not come out. Once pressurized, it blew out the tube and all over...
  5. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    Does anybody have any good walkthroughs on checking air leaks? I am pretty sure I am leaking air from my HSN. It runs great for 1/4 tank or so, then it dies. When I try to start it, there are air...
  6. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    After looking at my car a little more last night, I found out some other things also. My buggy was purchased about 3 weeks ago, and it is an old version of the BB. It has the aluminum bell which does...
  7. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    I fixed the image link, bigger picture now. They came loose and looks like the engine tourque pulled the heads through before they fell out. No flipping this time, just running around tuning it.
  8. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    How doI put them in? I tried to link them. You can follow the link below for now.

    picasaweb.google.com/lh/photo/YBxEupqNjC41ud14bYE8Bg
    ...
  9. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    Well, have not had too much luck with my Redcat. Here is the recent Damages!

    I was tuning it still, trying to get it to stay running through an entire tank, half throttle most of the time, full...
  10. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    Alright, I am losing hope and so is my friend.

    I have the Tornado BB. It has the SH18 and standard parts right now. I did the break in, and the engine locked in the up position on the 2nd tank. I...
  11. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    It does make sense. I will disassemble it tonight and check it over again. I am trying to make sure everything is good. I just did not think the noises sounded right and the gears were a little...
  12. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    I took it apart, and I looked it over. Seems as though 1 tooth is chippped on the 2nd gear, but all looks good. Bearings spin good, etc. But it may be my imagination or the fact that is almost 2 AM...
  13. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    Transmission Help... I have been running my Tornado BB pretty hard in the West Texas Dust. I clean it after every run, each run being about 4-6 tanks. I bent the dogbone on the front right, bent it...
  14. Replies
    3,670
    Views
    232,967

    RE: Redcat Racing Tornado Thread

    I am only 16 pages into this, and Ihave a pretty good size order to upgrade my clutch bell and the bearings. I can not locate the 5/16 Tension Pin for the clutch nut. Any help, or am I just missing...
Results 1 to 14 of 14
All times are GMT -6. The time now is 07:08 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.