Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Heli-NuBee

Page 1 of 30 1 2 3 4

Search: Search took 1.25 seconds.

  1. Replies
    2,708
    Views
    247,850

    I have had two different RCGF 46cc gas engines...

    I have had two different RCGF 46cc gas engines and an NGH-38GF gas four stroke engine in my Sportster and those three engine flew the plane quite well. I am now moving on to a DLE 55-RA rear exhaust...
  2. Replies
    965
    Views
    75,865

    I had my maiden flight today using the NGH 38GF...

    I had my maiden flight today using the NGH 38GF engine on my GP Super Sportster. The engine ran very well and flew the plane just fine. However, three of the four engine mounting bolts were loose...
  3. Replies
    965
    Views
    75,865

    I used red locktight on the engine bolts that...

    I used red locktight on the engine bolts that came loose and let it cure for a full day. I then ran the engine again and did some additional tuning. The engine is running much better now but still...
  4. Replies
    965
    Views
    75,865

    I did a test run on the NGH-38GF engine powered...

    I did a test run on the NGH-38GF engine powered GP Super Sportster today. I got the engine running much better. The low needle was quite rich and tuning helped the low end shaking. However, the...
  5. Replies
    207
    Views
    21,813

    I did a test run on the NGH-38GF engine powered...

    I did a test run on the NGH-38GF engine powered GP Super Sportster today. I got the engine running much better. The low needle was quite rich and tuning helped the low end shaking. However, the...
  6. Replies
    965
    Views
    75,865

    OK, it is time to move on. I am now installing...

    OK, it is time to move on. I am now installing my NGH 38 GF engine in my GP Giant Super Sportster. I will post additional details and pictures in the near future.

    Best wishes and good safe...
  7. Replies
    2,095
    Views
    220,526

    When I purchased the BF-109 from Nitro Planes,...

    When I purchased the BF-109 from Nitro Planes, the air retracts were listed as an accessory for about $40.00.

    Best wishes and good safe flying.

    Heli-NuBee (AKA Roger the redial rabbit)
  8. Replies
    965
    Views
    75,865

    I had my maiden flights on the 109 Wednesday...

    I had my maiden flights on the 109 Wednesday morning. The plane flew very well and the engine ran great. The only issue encountered was the tendency for the landing gear to bounce if one trys to turn...
  9. Replies
    207
    Views
    21,813

    I had my maiden flights on the 109 Wednesday...

    I had my maiden flights on the 109 Wednesday morning. The plane flew very well and the engine ran great. The only issue encountered was the tendency for the landing gear to bounce if one trys to turn...
  10. Replies
    2,095
    Views
    220,526

    I had my maiden flights on the 109 Wednesday...

    I had my maiden flights on the 109 Wednesday morning. The plane flew very well and the engine ran great. The only issue encountered was the tendency for the landing gear to bounce if one trys to...
  11. Replies
    965
    Views
    75,865

    Just a quick update - I installed a Dave Platt...

    Just a quick update - I installed a Dave Platt spinner on the NGH 35 and did a bit more tuning while completing additional break-in engine runs. The engine now runs much smoother and my CMP BF-109...
  12. Replies
    207
    Views
    21,813

    I installed a Dave Platt spinner and did some...

    I installed a Dave Platt spinner and did some more break-in runs with a bit of tuning and the engine is now running much smoother. My CMP BF-109 is now ready for its maiden flight.
    ...
  13. Replies
    2,095
    Views
    220,526

    I painted the spinner and completed another...

    I painted the spinner and completed another engine break-in run. The engine is running much smoother with the big spinner and a little tuning. My plane is now ready for its maiden flight.
    ...
  14. Replies
    2,095
    Views
    220,526

    Making a bit of progress again. I received the...

    Making a bit of progress again. I received the reducing bushing from Tru Turn for the Dave Platt spinner backplate. Tru Turn was a bit expensive but the bushing was a perfect fit so it was worth...
  15. Replies
    2,095
    Views
    220,526

    OK, moving forward. I replaced one of the new...

    OK, moving forward. I replaced one of the new Hitec 645 MG servos that went bad and put lock tight on all of the servo screws. I also ordered a reducing bushing from Tru Turn for my Dave Platt...
  16. Replies
    965
    Views
    75,865

    I checked into RC Japan and their price seems...

    I checked into RC Japan and their price seems pretty good until you get the shipping and the 3.5% fee for using a credit card or Pay Pal. The only advantage to purchasing from them would be for...
  17. Replies
    965
    Views
    75,865

    Thanks SrTelemaster150 - I will look into RC...

    Thanks SrTelemaster150 - I will look into RC Japan.

    Best wishes and good safe flying.

    Heli-NuBee (AKA Roger the radial rabbit)
  18. Replies
    965
    Views
    75,865

    OK guys, thanks for the suggestions but I have...

    OK guys, thanks for the suggestions but I have previously posted that I gave away a Saito 180 because it had too much vibration and was damaging the airframe. Saito's have a good reputation and I...
  19. Replies
    310
    Views
    43,931

    A sad day for me. My Gilmore Red Lion went in...

    A sad day for me. My Gilmore Red Lion went in today at full throttle. I lost control of the plane near the end of the second flight. Everything is distroyed, batteries, plane, servos, receiver and...
  20. Replies
    66
    Views
    8,543

    A sad day for me. My Gilmore Red Lion went in...

    A sad day for me. My Gilmore Red Lion went in today at full throttle. I lost control of the plane near the end of the second flight. Everything is distroyed, batteries, plane, servos, receiver and...
  21. Replies
    207
    Views
    21,813

    Update, I replaced my NGH 38GF four-stroke engine...

    Update, I replaced my NGH 38GF four-stroke engine in my CMP BF-109 with an NGH 35GX two-stroke engine due to excessive vibration. The new NGH 35 CC engine runs great but also has a lot of vibration....
  22. Replies
    965
    Views
    75,865

    Update, I replaced my NGH 38GF four-stroke engine...

    Update, I replaced my NGH 38GF four-stroke engine in my CMP BF-109 with an NGH 35GX two-stroke engine due to excessive vibration. The new NGH 35 CC engine runs great but also has a lot of vibration....
  23. Replies
    2,095
    Views
    220,526

    More issues, the engine vibrated the screws out...

    More issues, the engine vibrated the screws out of three servos during only three tank fulls of fuel. It seems as thoulgh the NGH line of engines leaves something to be desired when it comes to...
  24. Replies
    2,095
    Views
    220,526

    OK, I ran into just a bit of a problem today. My...

    OK, I ran into just a bit of a problem today. My Dave Platt spinner backplate center hole is larger than my engine crankshaft. I e-mailed Mr. Platt and hope he has a reducing bushing available. I...
  25. Replies
    2,095
    Views
    220,526

    Making a bit of progress now. I replaced the NGH...

    Making a bit of progress now. I replaced the NGH 38GF engine with an NGH 35GX two stroke engine. I also reinforced the motor mount with 1/2" plywood on the bottom and 1/8" x 1/2" x 4" long alum...
Results 1 to 25 of 749
Page 1 of 30 1 2 3 4
All times are GMT -6. The time now is 04:01 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.