Search: Posts Made By: RCPAUL
Showing results 1 to 25 of 500
Search took 0.55 seconds.
Forum: Kit Building
11-09-2018, 08:42 AM
Replies: 3
Views: 289
Posted By RCPAUL

I think those are the wings to a Christenson...

I think those are the wings to a Christenson Eagle ARF. If so, there will be no plans.
Forum: Kit Building
09-27-2018, 09:46 AM
Replies: 17
Views: 388
Posted By RCPAUL

I tried Rustoleum clear several years ago and it...

I tried Rustoleum clear several years ago and it was not fuelproof. Mayb the formula has changed since the New?.
Forum: RC Jets
05-12-2018, 08:32 AM
Replies: 39
Views: 1,752
Posted By RCPAUL

I have never been to the site before but after...

I have never been to the site before but after reading the wide differences people are having, I just went to see what all the noise is about. I am using an IPad and everything seemed fine. It must...
05-12-2018, 06:39 AM
Replies: 3
Views: 469
Posted By RCPAUL

Oil based polyurethane. In the hardware stores...

Oil based polyurethane. In the hardware stores here.
02-27-2018, 01:18 AM
Replies: 4
Views: 989
Posted By RCPAUL

Wasn't there another published here, maybe in...

Wasn't there another published here, maybe in Flying Models?
Forum: Control Lines
01-11-2018, 07:52 AM
Replies: 18
Views: 2,636
Posted By RCPAUL

CA hinges can be stiff, decreasing the smoothness...

CA hinges can be stiff, decreasing the smoothness of control inputs. I like either the pinned hinged flat nylon or the Robart hinges.
11-27-2017, 09:53 AM
Replies: 12
Views: 868
Posted By RCPAUL

That sounds very excessive. Have you called...

That sounds very excessive. Have you called Brodak? You may have got a bad one - much too tight.

paul
Forum: Beginners
11-23-2017, 09:02 AM
Replies: 8
Views: 352
Posted By RCPAUL

Jester s1 10cc is 0.61 cui, not .40. ...

Jester s1

10cc is 0.61 cui, not .40.

paul
11-10-2017, 01:18 PM
Replies: 14
Views: 785
Posted By RCPAUL

I think you want a tractor engine in a pylon. ...

I think you want a tractor engine in a pylon. Balsa USA has a coule of kits.
Forum: Control Lines
10-17-2017, 08:16 AM
Replies: 17
Views: 1,509
Posted By RCPAUL

I heard of an RC club that lost access to a large...

I heard of an RC club that lost access to a large open sod farm when the owner found out that the fuel would kill his grass.
09-04-2017, 10:09 AM
Replies: 18
Views: 770
Posted By RCPAUL

Nice response!

Nice response!
08-17-2017, 06:30 AM
Replies: 5
Views: 914
Posted By RCPAUL

Horace Caine

A while back (and it's getting to be quite a while), there was a fellow who was very active posting on the forums, especially the AMA forum. His name was Horace Caine and at one time he was an AMA VP...
Forum: The Clubhouse
08-15-2017, 05:12 AM
Replies: 4
Views: 530
Posted By RCPAUL

Be careful. That coating maybe for UV protection...

Be careful. That coating maybe for UV protection and I doubt you want sunglasses without it!

paul
05-25-2017, 08:17 AM
Replies: 20
Views: 580
Posted By RCPAUL

What is the recommended clear coat for latex?

What is the recommended clear coat for latex?
Forum: Gas Engines
05-14-2017, 05:31 AM
Replies: 6
Views: 550
Posted By RCPAUL

DLE20RA a couple of questions.

Im new to gas but have been flying nitro for over 65 years.

First, do you disconnect the throttle spring? If so, how?

Second, can anyone recommend a motor mount for this engine?

Thanks,
Paul
05-02-2017, 08:49 AM
Replies: 9
Views: 1,650
Posted By RCPAUL

Fascinating build and excellent work!

Fascinating build and excellent work!
04-30-2017, 12:11 AM
Replies: 12
Views: 405
Posted By RCPAUL

My page - how?

My page - how?
Forum: Glow Engines
04-29-2017, 10:31 AM
Replies: 6
Views: 1,069
Posted By RCPAUL

I for one am impressed by your skills! paul

I for one am impressed by your skills!

paul
04-29-2017, 08:02 AM
Replies: 12
Views: 405
Posted By RCPAUL

When I log on, I get treads on subjects that I...

When I log on, I get treads on subjects that I have not subscribed to. Like tanks, various car threads, etc. None of these are in my subscribed list. How do I eliminate them showing up. I think this...
04-19-2017, 09:46 AM
Replies: 3
Views: 749
Posted By RCPAUL

Go to Valley Aviation, enter the site (bottom of...

Go to Valley Aviation, enter the site (bottom of page), and at the bottom of the page that comes up,there is an article on exact subject your asking about. And, it is excellent.

paul
04-18-2017, 04:36 AM
Replies: 11
Views: 1,723
Posted By RCPAUL

I haven't used belcranks for years. With smaller,...

I haven't used belcranks for years. With smaller, more powerful, lighter servos, the dual ( or quad) servo approach is best for most applications.
04-16-2017, 05:37 AM
Replies: 9
Views: 2,827
Posted By RCPAUL

You might want to get a detail gun. Harbor...

You might want to get a detail gun. Harbor Freight has one that is inexpensive.
Forum: The Clubhouse
03-07-2017, 07:44 AM
Replies: 5
Views: 629
Posted By RCPAUL

I get the pop up as well.

I get the pop up as well.
01-26-2017, 11:29 AM
Replies: 27
Views: 1,482
Posted By RCPAUL

I don't think it is degummed. A little is ok but...

I don't think it is degummed. A little is ok but don't over do.
01-14-2017, 09:51 AM
Replies: 10
Views: 2,693
Posted By RCPAUL

Where does it say they are going out of business?

Where does it say they are going out of business?
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service