Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: MrMikeG

Page 1 of 40 1 2 3 4

Search: Search took 0.45 seconds.

  1. Replies
    27
    Views
    1,509

    RE: Zen not starting

    Classic 644 problems.
    With the jug off run a drill bit (by hand) through the pulse port and iso-block, this insures it's not blocked!
    When you reassemble make sure the carb gaskets don't move...
  2. Replies
    16
    Views
    1,110

    RE: Race Pictures

    Miami to Ohio to Italy to Australia, under $200 total, you just have to know how to get around the size regulations and have good friends you can count on! ;) Came in less than 2 weeks too! :)
  3. Replies
    27
    Views
    1,509

    RE: Zen not starting

    how long have you had the engine?
  4. Replies
    2
    Views
    520

    RE: Mysterry boat & motor

    just guessing but it looks like a stihl engine
  5. Replies
    4
    Views
    369

    RE: AM,or FM Radio?

    FM is better. For failsafe issues at distance like that check your batteries, make sure they are up to scratch. 6Volts.
  6. Replies
    16
    Views
    1,110

    RE: Race Pictures

    My guess would be that baby got run up the beach! [:@]

    Great pics, my Insane Cat came from Sal and it still has the RAM sticker on it! ;)
  7. Replies
    26
    Views
    1,531

    RE: more Rio 51 woes

    Stick with it, half this hobby is in the Engineering! ;)
  8. Thread: graffics

    by MrMikeG
    Replies
    13
    Views
    1,509

    RE: graffics

    Major smackdown has graphics for Deep-vee style boats too.
  9. Replies
    34
    Views
    4,553

    RE: MHZ GTX BUILD

    You really should try to make the header pipes the same length, otherwise the engines are going to be out of sync.
  10. Replies
    50
    Views
    3,327

    RE: 54" Gasser The Project Resumes

    The Mac has roller bearings that will fail first if you run for any length of time. The Homelite is easiest. Personally I would Ebay all 3 and go with a Zenoah, you can try the new RCMK's if you want...
  11. Replies
    50
    Views
    3,327

    RE: 54" Gasser The Project Resumes

    The wrap traps water in and will rust your pipes out.
  12. Replies
    23
    Views
    1,485

    RE: rio 51 want to put a bigger motor in

    I would guess the Fuji to be 2 hp or less. [8D]
  13. Replies
    26
    Views
    2,244

    RE: Edit: homelite drive setup

    It's not that hard to solder your own ferrels onto the cable, then you can get cables with only one square end cheap and make as many as you want. Remember there is a bit of engineering in this...
  14. Replies
    81
    Views
    4,706

    RE: Rockett zippkit build

    Poly, I would stick with all one type of resin. I have used "Mat" with epoxy too but you need thinner layers. The binder in mat is starch and it acts like a thickener with epoxy.
  15. Replies
    2
    Views
    1,138

    RE: motul 800 oil

    I used to run TTS, never killed an engine yet! I run 20:1, and I'm not one brand specific. I ran through 5 liters of Klotz, probably close to 10 liters of Castrol A747 and now I'm onto Fuch's...
  16. Replies
    50
    Views
    3,327

    RE: 54" Gasser The Project Resumes

    you will have to seal them really good, basswood isn't ply is it? Every hole you drill will need to be sealed or the water will get in and rot the wood. [:-]
  17. Replies
    14
    Views
    1,222

    RE: Engine Compression

    I think the lower limit for gas to fire is 85 psi, under that and it just won't run.
  18. Replies
    11
    Views
    1,211

    RE: Anyone in Vancouver area?

    My "Local club" is 400 km's away too! [8D]
  19. Replies
    11
    Views
    1,211

    RE: Anyone in Vancouver area?

    Andy from AC is in Kelowna, BC
  20. Replies
    66
    Views
    3,849

    RE: My New Thunderboat

    More bracing, pay close attention to the back of the sponsons. ;)
  21. Replies
    11
    Views
    1,139

    RE: Zippkit-Rockett throttle set up Help

    Henry, here is a picture of Joe's set-up, I think Mat uses an up and down bell crank set up but couldn't find a pic of it.
  22. Replies
    15
    Views
    2,418

    RE: Source for 1/4" flex Shafts ( FREE )

    just wait till you break a straight cable and loose cable,prop and drive dog. [8D] With square drive it is a lot harder to loose a prop.
  23. Thread: Radios

    by MrMikeG
    Replies
    3
    Views
    413

    RE: Radios

    check with these guys, good prices and usually quick shipping, even from WA.
    http://www.ozshops.com/cgi-bin/RT_Resp.cgi?application=radio
  24. Replies
    15
    Views
    2,418

    RE: Source for 1/4" flex Shafts ( FREE )

    no no don't buy, I get mine from the trimmer shop as well, just letting you know what to look out for. [8D]
    It's not the stuffing tube that cares about the diameter it is the solder on ferrels, if...
  25. Replies
    5
    Views
    506

    RE: I-Box maiden

    Looks great! What prop are you running on the I-Box?
    Good to see your keeping busy, great to know you got the bug big time! :D
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 05:34 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.