Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Redcat James

Page 1 of 3 1 2 3

Search: Search took 0.04 seconds.

  1. I would reset the needle settings to the stock...

    I would reset the needle settings to the stock settings. Turn both the high and low speed needles clockwise until they bottom out. Back the high speed needle out 3-1/2 turns and the low speed 2-1/4...
  2. I would recheck the needle settings, the idle...

    I would recheck the needle settings, the idle setting and the clutch. I would also check the glow plug.
  3. Replies
    2
    Views
    87

    Where is the ST/DR knob set to?

    Where is the ST/DR knob set to?
  4. http://www.redcatracing.com/02092

    http://www.redcatracing.com/02092
  5. Replies
    9
    Views
    569

    Actually we say that because the esc, motor and...

    Actually we say that because the esc, motor and gearing are designed for 2s lipo.
  6. Replies
    6
    Views
    109

    http://www.redcatracing.com/108839

    http://www.redcatracing.com/108839
  7. Replies
    9
    Views
    569

    The Tornado EPX Pro is only rated out of the box...

    The Tornado EPX Pro is only rated out of the box for a 2s lipo battery, adding a 3rd cell will void the warranty.
  8. Did you try the dual rate knob? It should be set...

    Did you try the dual rate knob? It should be set to 6. There is no end point adjustment on a Tornado controller.
  9. This is a different esc but the manual and set up...

    This is a different esc but the manual and set up are the same. Click the manual link under description http://www.redcatracing.com/03351
  10. Replies
    3
    Views
    109

    Maybe the engine is overheating. Try richening it...

    Maybe the engine is overheating. Try richening it up.
  11. Replies
    11
    Views
    124

    If the car is on the ground and you slowly pull...

    If the car is on the ground and you slowly pull the pull starter up, will the car stay on the ground or come up with the pull start?
  12. Replies
    1
    Views
    48

    Savox makes good servo's at reasonable price.

    Savox makes good servo's at reasonable price.
  13. Replies
    11
    Views
    124

    Are you still using the pull start?

    Are you still using the pull start?
  14. Replies
    11
    Views
    124

    If the clutch spring is good the clutch sounds...

    If the clutch spring is good the clutch sounds like it's ok. The engine could just be worn out and needs to be rebuilt or replaced. May not have enough power to make it shift? You said the engine...
  15. Replies
    11
    Views
    124

    Does the clutch bell spin freely on the engine?

    Does the clutch bell spin freely on the engine?
  16. The antenna should be about 2" long. If it was...

    The antenna should be about 2" long. If it was cut then that could be your problem. If the antenna was not cut then more than likely your PCB board is bad. Here is the part number 24620.
  17. Replies
    3
    Views
    109

    If the car is on the ground and you slowly pull...

    If the car is on the ground and you slowly pull the pull start, does the car stay on the ground or pick up with the pull cord?
  18. Replies
    5
    Views
    114

    http://www.redcatracing.com/03351 Sorry

    http://www.redcatracing.com/03351 Sorry
  19. Replies
    5
    Views
    114

    Go to the manual link at the bottom, it tells you...

    Go to the manual link at the bottom, it tells you how to turn off the low voltage cut off that I believe is causing your issues. Or at least I would start there.
  20. 160 degrees should be fine all day long.

    160 degrees should be fine all day long.
  21. Replies
    1
    Views
    58

    Did you run the truck until it stopped moving...

    Did you run the truck until it stopped moving last time you used it or leave the battery plugged in? The battery could be bad or too low a voltage for the charger to recognize it. If you have a...
  22. Replies
    5
    Views
    114

    Possibly the low voltage cut off is set too high....

    Possibly the low voltage cut off is set too high. What is the battery voltage?
  23. Replies
    19
    Views
    227

    Nightwolfe, sounds like you esc is bad and it's...

    Nightwolfe, sounds like you esc is bad and it's cogging.
  24. Replies
    2
    Views
    92

    Sounds like either the voltage is too low or too...

    Sounds like either the voltage is too low or too high. It don't work with more than 4s lipo.
  25. Check the voltage coming out of the battery...

    Check the voltage coming out of the battery holder and make sure it's plugged in correctly. If it was plugged in backwards, you could have damaged the receiver.
Results 1 to 25 of 63
Page 1 of 3 1 2 3
All times are GMT -6. The time now is 06:03 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.