Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: aquaskiman

Page 1 of 40 1 2 3 4

Search: Search took 0.97 seconds.

  1. Replies
    387
    Views
    31,730

    I saw it when you posted it. I fly jets most of...

    I saw it when you posted it. I fly jets most of the time, the reason you did not get much of a response it that jets don't use that type of retract. Most of the jet gear of today are pretty strong...
  2. Replies
    387
    Views
    31,730

    I know .....for what you pay you would think it...

    I know .....for what you pay you would think it could take a little side load.
  3. Replies
    387
    Views
    31,730

    Have pulled the retract apart and found that a...

    Have pulled the retract apart and found that a pin on the upper trunnion has bent which jams the gear. I have used Robart electric retracts on this model, and they weren't a cheap option!!:mad: I...
  4. Replies
    0
    Views
    119

    Skymaster 1/6.5 F-86

    If any one has bought a skymaster 1/6.5 F-86 in the last year I would like to know the wingspan. It is advertised as 68 inch wingspan and up to a 22lb turbine. I had one I bought 4 or 5 years ago and...
  5. Replies
    826
    Views
    57,686

    Air Leak see post 693

    Air Leak see post 693
  6. Replies
    826
    Views
    57,686

    Check and make sure the O ring in in place...

    Check and make sure the O ring in in place between the carb and intake manifold there is supposed to be two, one inside the carb where it mounts on the bushing and another between the carb, manifold....
  7. Replies
    826
    Views
    57,686

    The bushing is held in place with a small set...

    The bushing is held in place with a small set screw on the bottom. It is red loctited in place so you will need to heat it to get it loose.
  8. Replies
    14
    Views
    960

    batteries 3 2 RX and 1 ecu checked and tested ok

    batteries 3 2 RX and 1 ecu checked and tested ok
  9. Replies
    14
    Views
    960

    The fail safe was set correctly and tested before...

    The fail safe was set correctly and tested before and after. The range test was tested before and after. So if the transmitter failed it should of shut the turbine down. It was not just the throttle...
  10. Replies
    14
    Views
    960

    The pilot of the plane has another radio and this...

    The pilot of the plane has another radio and this was the last plane on this radio. So he is not going to use it again. It is a little concerning for those of us that use the 6014HS, but like I said...
  11. Replies
    14
    Views
    960

    I fly with a 12Z and use the 6014HS and never a...

    I fly with a 12Z and use the 6014HS and never a glitch. This jet in question has many trouble free flights on it with the receiver in the same place. I looked at the antennas and they were at 90 deg.
  12. Replies
    826
    Views
    57,686

    If the valves are sealing when the cylinder is...

    If the valves are sealing when the cylinder is off or the rocker arms are removed and leaking when it is put together than something is holding the valve open. A close up pic would help.
  13. Replies
    1
    Views
    178

    6014HS unlink

    Has anyone heard of this before? A friend of mine had a 6014HS unlink, this is what happened. He had flown his Lightning a few days before and all was fine. He started it up taxed to the runway,...
  14. Replies
    826
    Views
    57,686

    can you post a close up pic of the rocker arms at...

    can you post a close up pic of the rocker arms at TDC on compression stroke?
  15. Replies
    14
    Views
    960

    Futaba 6014HS unlinked

    Has anyone heard of this before? A friend of mine had a 6014HS unlink, this is what happened. He had flown his Lightning a few days before and all was fine. He started it up taxed to the runway,...
  16. Replies
    826
    Views
    57,686

    If you have a air compressor watch the intake...

    If you have a air compressor watch the intake valve open than close than turn to TDC and put some air through plug hole, listen for the air to come out. You most likely have a stuck valve. If so put...
  17. Replies
    1
    Views
    377

    Wonder if it will run without spending $300 to...

    Wonder if it will run without spending $300 to $500 on it
  18. Replies
    387
    Views
    31,730

    Yes I did use the saito R3 I added about 8 oz of...

    Yes I did use the saito R3 I added about 8 oz of weight. after I flew it at the stock balance. I wanted it a little more nose heavy. I also reduced the flap to 30 deg George
  19. Replies
    387
    Views
    31,730

    here is a pic of mine when it was almost done

    here is a pic of mine when it was almost done
  20. Replies
    6,696
    Views
    618,949

    there is always one like you

    there is always one like you
  21. Replies
    6,696
    Views
    618,949

    Oh....This isn't complaining?????????????? I...

    Oh....This isn't complaining?????????????? I didn't say ship for free READ THE POST
  22. Replies
    6,696
    Views
    618,949

    You guys that are complaining about shipping, get...

    You guys that are complaining about shipping, get real, you buy on line you pay shipping one way or another. Do you guys work for free???? So why do you think someone should take your parts to the...
  23. Replies
    459
    Views
    48,856

    Dave do you know if springs are available for the...

    Dave do you know if springs are available for the Xcal + landing gear?
  24. Replies
    11
    Views
    764

    Shaun what is your glow plug voltage? I use 2.2...

    Shaun what is your glow plug voltage? I use 2.2 volts
  25. Replies
    826
    Views
    57,686

    No it seemed to run about the same. It stayed in...

    No it seemed to run about the same. It stayed in tune better. The choke is nice
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
RCU Reviews
All times are GMT -6. The time now is 12:54 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.