Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Xeller8

Page 1 of 19 1 2 3 4

Search: Search took 1.14 seconds.

  1. Replies
    22
    Views
    1,057

    RE: Aluminum door mounts pic on my truck.

    You HOPE it's a better grade of plastic.;)

    But they actually DO look a little bit "meatier" than the stock ones.
  2. Replies
    14
    Views
    1,380

    RE: lock(too)tight

    O.K..now that you clarified that and I re-read the post it makes sense...

    It's been a long day....D'OH!...LOL!
  3. Replies
    4
    Views
    425

    RE: traxxas shoes

    Well...you will definitely have higher revs before it engages so it will launch a lot harder.

    Don't know what else to tell you from there cept...

    Good luck!:D
  4. Replies
    14
    Views
    1,380

    RE: lock(too)tight

    HUH?
  5. Replies
    45
    Views
    2,057

    RE: two speed or one?

    After reading all the negative about the 2-speeds being all but impossible to set so they shift correctly I wouldn't waste the money...put the money towards better radio gear instead.
  6. Replies
    180
    Views
    15,810

    RE: Volcano STX truck

    Just make sure you have the mesh set correctly and the engine square with the tranny when you put it back together....otherwise....you buy gears.
  7. Replies
    180
    Views
    15,810

    RE: Volcano STX truck

    You beat me to it Dennis.[8D]
  8. Replies
    18
    Views
    961

    RE: Clutch Slice- Quick Question

    My LHS is a little over a half hour away too...but when I need stuff....I just.......GOOOOOOOOO!:D
  9. Replies
    18
    Views
    961

    RE: Clutch Slice- Quick Question

    You should be able to find the Traxxas spring (or ANY better spring) at your LHS...just take it in and compare.
  10. Replies
    13
    Views
    807

    RE: tires spin at idle

    Sticky to top of forum happen after having clutch slice.
  11. Replies
    18
    Views
    961

    RE: Clutch Slice- Quick Question

    "Clutch slice"

    That STILL makes me giggle.
  12. Replies
    7
    Views
    458

    RE: got a problem

    Clean the outside off really good first...use some spray carb cleaner or something like that....then take the head off and check the top of the piston and see if is are scorched or looks blued...if...
  13. Replies
    16
    Views
    982

    RE: Clutch bell warped teeth

    W-T-F!!!!!?????

    Was the guys name Corky by any chance??...was he wearing a helmet and trying to lick the glass on your windows too??
  14. Replies
    13
    Views
    807

    RE: tires spin at idle

    Yeah...I think Darin or one of the mods would have to "sticky" it though...

    I don't think us regular ole garden variety low-life posters can do it...LOL.
  15. Replies
    7
    Views
    458

    RE: got a problem

    Check the head bolts and make sure they are snug...I had the same problem with MY 'Cane XP and it turned out my head bolts were loose...that will cause a lean condition (excess air entering the...
  16. Replies
    13
    Views
    807

    RE: tires spin at idle

    Sounds like a great idea Steve...the only thing is that newbies will STILL start new threads with the same questions over and over again instead of SEARCHING the forums first...LOL!:D

    Can't hurt...
  17. Replies
    26
    Views
    1,256

    RE: volcano stx piston

    Oh I'm not saying it WOULD'NT work....my concerns are more about room to work with....like where would you put the battery pack and the receiver if you were to give up access to the receiver...
  18. Replies
    26
    Views
    1,256

    RE: volcano stx piston

    I was looking it over pretty extensively the other night and I really don't see a real good way to do that....the way you mentioned MIGHT be something that would work but I think adding in another...
  19. Replies
    10
    Views
    2,020

    RE: infinity engine

    I put a Sportwerks .26 in mine...(used in the Mayhems) it's the same motor as a Dynamite Mach .26....very good motor....tons of power and easier to tune than the Infinity....one other cool thing...
  20. Replies
    13
    Views
    807

    RE: tires spin at idle

    You don't want to richen up even more if you already have fuel coming out of the exhaust and you don't want to make idle adjustments with the low speed mixture needle...use the idle screw (little...
  21. Replies
    26
    Views
    1,256

    RE: volcano stx piston

    Hey Chopper....I hope you didn't order that .18 that Ehroof listed above....that one has a slide carb and WON'T WORK on these trucks...not sure if you saw my post last night before so many of them...
  22. Replies
    50
    Views
    4,523

    RE: Post links to your Redcat Racing Videos

    Man....Putfile BLOWS!...can't get the vid to download![:@]

    Have any of you tried Rapidshare??...seeme to work a LOT better...the only thing is that it is not permanent storage and if the file...
  23. Replies
    11
    Views
    912

    RE: Part # 81010 steering wheel set?

    LMAO!!...If you have no idea where they go why did you buy them in the first place?
  24. RE: "OFFICIAL" Redcat Racing 1/8th BUGGY thread (not truck thread)

    Check all your plugs on the receiver...they like to come loose sometimes.
  25. Replies
    12
    Views
    468

    RE: please help!

    Oh god no...if you are going to upgrade go FM dude.
Results 1 to 25 of 473
Page 1 of 19 1 2 3 4
All times are GMT -6. The time now is 05:31 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.