Futaba 14SGA 14-Channel Air Computer System
04-27-2018, 10:17 AM
#1
Thread Starter
My Feedback: (43)
Join Date: Jun 2005
Location: Mulberry, FL
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
Futaba 14SGA 14-Channel Air Computer System
Brand new in the box Futaba 14SGA 14-Channel Transmitter, Receiver, Switch Harness, Transmitter Battery and complete manual. And, four new metal gear Savox Servos.
Also, Included are 4 Savox metal gear high torque channels. Only one of these servos has been opened (never used) and the other three are still Shrink wrapped.
One Savox SH-1290MG
Specifications:
Specifications:
Buyer pays $25.00 for shipping. And, I will only accept PayPal. I will only ship within the United States
- channels: 12 proportional, 2 switched
- Compatible with FASSTest, FASST and S-FHSS protocols
- FASSTest telemetry compatible with Futaba telemetry sensors (sold separately)
- Free user-updatable software
- 30-model memory
- 10-character user naming
- 10-character model naming
- Airplane, helicopter and glider programming
- Large, 1.75 x 3 backlit LCD screen with 128 x 64 resolution
- SensorTouch programming
- Compatible with secure digital memory cards for external storage of model setups and software updates (32MB-2GB or HC (High-Capacity) 4GB-32GB)
- Left and right assignable slider switches
- Two assignable rotary knobs
- Six assignable three-position switches
- One assignable momentary two-position switch
- One assignable two-position switch
- Comfortable rubber grips on the sides and back
- Wide top switch spacing
- Adjustable stick tension
- Dual ball bearing gimbals
- 4 vibration warning types
- Home/Exit; User Menu/Servo Monitor buttons
- Audio earphone jack (for telemetry alarms)
- 6V 1800mAh NiMH battery pack
- User stick calibration
- Trainer system
- Servo speed adjust
- 5 programmable mixes
- V-tail, Ailvator, winglet, motor mixing
- Trim mix
- Logic switch (condition switch only)
- Internal programmer for S.Bus servos
- User menu
- Servo monitor (neutral and moving tests)
- 2 count up/countdown timers
- Integral timer
- Model timer
- Quick model select
Also, Included are 4 Savox metal gear high torque channels. Only one of these servos has been opened (never used) and the other three are still Shrink wrapped.
One Savox SH-1290MG
Specifications:
- Speed @ 6.0V: 0.04 sec/60°
- Torque @ 6.0V: 69 oz-in / 5 kg-cm
- Weight: 56.4g
- Type: Standard
- Gear: Metal
- Case: AluminumHeatsink
- Case Size (LxWxH): 40.3x20x37.2mm
Specifications:
- Speed @ 6.0V: 0.07 sec/60°
- Torque @ 6.0V: 138 oz-in / 10 kg-cm
- Weight: 52.4g
- Bearing: Dual
- Type: Standard
- Gear: Titanium and Aluminum
- Case: Aluminum Heatsink
- Output Shaft: 25T Spline (Futaba)
- Case Size (LxWxH): 40.3x20x37.2mm
Buyer pays $25.00 for shipping. And, I will only accept PayPal. I will only ship within the United States
Last edited by Tspenader; 04-29-2018 at 10:35 AM.
04-28-2018, 07:32 AM
#3
Thread Starter
My Feedback: (43)
Join Date: Jun 2005
Location: Mulberry, FL
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
Offer for Equipment
Originally Posted by [email protected]
$300 Shiping to orlando FL 34743. Paypal thanks
04-28-2018, 02:44 PM
#5
Thread Starter
My Feedback: (43)
Join Date: Jun 2005
Location: Mulberry, FL
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
The battery is for the transmitter not the receiver. Only one receiver is included. The pictures turned out rather soft, so I just wanted to make sure that everyone could clearly see the model number.
