EQ6 - adjusting multiple servos on channel 1 (ailerons)
02-10-2010, 08:39 PM
#1
Thread Starter
Join Date: Mar 2007
Location: , IL
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
EQ6 - adjusting multiple servos on channel 1 (ailerons)
When I try to adjust the servos (for centering) on channel 1 (ailerons) on the EQ-6 the servos don't change. I have an Futaba 14 channel FASST receiver. I have the Smartfly pigtails as follows: 1 on smartfly to 1 on receiver, 2 on smartfly to 2 or receiver, 3 on Smartfly to 3 on receiver, etc. I plan on using flaperon and have the ailerons plugged into channels 1 and 6. I have 4 aileron servos (2 for each wing) Am I correct in plugging the 2 left aileron servos into channel 1 on the Smartfly and the 2 right ones into channel 6? I notice channel 1 does not have an A or B marking or an LED?
02-10-2010, 09:26 PM
#2
My Feedback: (1)
Join Date: May 2003
Location: North Las VegasNV
Posts: 789
Likes: 0
Received 0 Likes
on
0 Posts
RE: EQ6 - adjusting multiple servos on channel 1 (ailerons)
the two left aileron servos should be pluged into channel 2 on the smart fly Eq6.
Channel one is throttle.
I may be wrong, I am relating to my JR921 reciever where cannel one is throttle, 2 is aileron, 3 is eleviator, 4 is rudder and so on.
Channel one is throttle.
I may be wrong, I am relating to my JR921 reciever where cannel one is throttle, 2 is aileron, 3 is eleviator, 4 is rudder and so on.
02-11-2010, 09:24 AM
#3
Senior Member
Join Date: Sep 2004
Location: Tempe,
AZ
Posts: 949
Likes: 0
Received 0 Likes
on
0 Posts
RE: EQ6 - adjusting multiple servos on channel 1 (ailerons)
ORIGINAL: NiknJen
When I try to adjust the servos (for centering) on channel 1 (ailerons) on the EQ-6 the servos don't change. I have an Futaba 14 channel FASST receiver. I have the Smartfly pigtails as follows: 1 on smartfly to 1 on receiver, 2 on smartfly to 2 or receiver, 3 on Smartfly to 3 on receiver, etc. I plan on using flaperon and have the ailerons plugged into channels 1 and 6. I have 4 aileron servos (2 for each wing) Am I correct in plugging the 2 left aileron servos into channel 1 on the Smartfly and the 2 right ones into channel 6? I notice channel 1 does not have an A or B marking or an LED?
When I try to adjust the servos (for centering) on channel 1 (ailerons) on the EQ-6 the servos don't change. I have an Futaba 14 channel FASST receiver. I have the Smartfly pigtails as follows: 1 on smartfly to 1 on receiver, 2 on smartfly to 2 or receiver, 3 on Smartfly to 3 on receiver, etc. I plan on using flaperon and have the ailerons plugged into channels 1 and 6. I have 4 aileron servos (2 for each wing) Am I correct in plugging the 2 left aileron servos into channel 1 on the Smartfly and the 2 right ones into channel 6? I notice channel 1 does not have an A or B marking or an LED?
Rx Ch 1 -> Eq6 Ch 2 (Aileron)
Rx Ch 2 -> Eq6 Ch 3 (Elevator
Rx Ch 3 -> Eq6 Ch 1 (Throttle)
Rx Ch 4 -> Eq6 Ch 4 (Rudder)
Rx Ch 5 -> Eq6 Ch 5 (Gear)
Rx Ch 6 -> Eq6 Ch 6 (Aux 1)
Rx Ch 7 -> Eq6 Ch 7 (Aux 2)
Rx Ch 8 -> Eq6 Ch 8 (Aux 3)
Let me know if you have any other questions.
