Project Miami Vice!!!! paint on page 2
#1
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
Project Miami Vice!!!! paint on page 2
my boat finally showed up!!!
this is going to be a very quick build, i'm hopping to have her done by the weekend
heres the specs
-super vee 27 motor and esc combo
-14ib 4200's
-theemed to look like the 39' mti form the movie
-all bby hardware
for this weekend she will be running on a fieago 14xl on twenty cells. its a long story
here's the boat:
and heres what the finished product will look like
this is going to be a very quick build, i'm hopping to have her done by the weekend
heres the specs
-super vee 27 motor and esc combo
-14ib 4200's
-theemed to look like the 39' mti form the movie
-all bby hardware
for this weekend she will be running on a fieago 14xl on twenty cells. its a long story
here's the boat:
and heres what the finished product will look like
#4
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
got it from www.bbyracing.com i can't wait either. at least it won't be long
#6
Senior Member
Join Date: Nov 2006
Location: Hudsonville,
MI
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
its not carbon fiber, its the scat cat 26 if he put 20 cells in a micro scat cat then it would sink into the ground not just water, lol
#7
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
ORIGINAL: FE_Chris
is that a Carbon Fibre micro scat cat? Nice..........
is that a Carbon Fibre micro scat cat? Nice..........
as allready stated nope. it's the abs 26. the 26 and micro look the same.....
i started to lay up fiberglass today but ran out. this puts me till wensday to statr mounting stuff up. should be in the water by saturday
#10
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
thanks. the date for running gear has been pushed back to thursday. it's going to be tight getting her in the water by saturday but i think it will be doable
#11
RE: Project Miami Vice!!!! now playing
awesome, now I just have to build a Donzi ZR 38 from the movie, of which I will gladly brag I rode in last week. Very nice handling boat, but black is very hot on the feet.
#12
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
ORIGINAL: Quicksilver
awesome, now I just have to build a Donzi ZR 38 from the movie, of which I will gladly brag I rode in last week. Very nice handling boat, but black is very hot on the feet.
awesome, now I just have to build a Donzi ZR 38 from the movie, of which I will gladly brag I rode in last week. Very nice handling boat, but black is very hot on the feet.
no ****, black is a terrible boat color. how fast? what engines, if it was the one from the movie it would be 575's. with 1075's thats donzi's fastest boat.
the only true gofast i've ever riden in was a 31' foot scarab with twin 525's. went 90mph with a slight chine walk. she was mildly over powered.
i got the glass all done and i started to join the hull but i ran out of super glue. the glass made her much stiffer
#13
RE: Project Miami Vice!!!! now playing
well apparently there were two boats. He got the slower of the two, though I'm not sure if they sold the other one. This had twin staggered 525's with XR drives.It tops out at just under 100mph, though we got it up to 87 in a 2-3ft chop. Very smooth boat, didnt notice any chine walk or the like. I ended up standing which turned out to be regretful...bad wind burn. I will post some pics when I get them. awaiting an e-mail. We actually ran into a cigarette top gun, which wanted to race very badly, but the owner didnt want to waste a few hundred bucks(gas) on the guy.
#14
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
yup there was two, a 38zr and a 43zr. both very underpowered but beacause of good hull design they were fast. i know what your saying about standing. i was wering sunglasses, not nearly enough. the driver had old school pilot googles. wish i had a pair.
the gas thing sucks. my familys boat has a single 425hp engine and that sucks the gas. a little more than 5 fill ups this summer at 300 dollars + a piece
the gas thing sucks. my familys boat has a single 425hp engine and that sucks the gas. a little more than 5 fill ups this summer at 300 dollars + a piece
#15
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
heres ome updated pics. i got the glass done and i'm now workin on joining the hull. i'm hoping to have the strudder and motor mount on by midnight tonight
#17
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
yup. mucho grande problema!!!!!
got the top glued on and now the hull is not level!!!!!!! should be interesting to see what it does on the water. $#%^ #$%^ &^%$ &*(@
throwing and kicking it helped my anger though
got the top glued on and now the hull is not level!!!!!!! should be interesting to see what it does on the water. $#%^ #$%^ &^%$ &*(@
throwing and kicking it helped my anger though
#19
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
what are you doing standing in the back seat? standing is only for the bolsters.
i used ca but it wants to rip instead of come apart. i'm thinking this is really not good. it's not terrible, it's like stick a matchbook under the table leg to level it out bad.
some creative wieght distribution when she's running?
i used ca but it wants to rip instead of come apart. i'm thinking this is really not good. it's not terrible, it's like stick a matchbook under the table leg to level it out bad.
some creative wieght distribution when she's running?
#24
Senior Member
Thread Starter
Join Date: Jun 2006
Location: mcyville,
WI
Posts: 566
Likes: 0
Received 0 Likes
on
0 Posts
RE: Project Miami Vice!!!! now playing
so then it should ride real nice. 1000hp in a 38ft boat going 100mph seems good to me but your the expert