Unofficial "NQD" Tear into Jetboat Thread
#2351
RE: Unofficial
ORIGINAL: skymaster62
Sundogz, you seem to be the goto guy in this thread. I have read the entire thread and have a question. If I am running 2200 mah 40-70C 2S with a 35a Turnigy water cooled ESC. With the given formula A=Ah x C
at 40 C I would be at 88a, and at 70C I would be at 156a. Depening on who you believe Turnigy max burst amps 150ish or Seaking max burst amps 70, am I heading for a melt down or is the water cooling making it workable.
Sundogz, you seem to be the goto guy in this thread. I have read the entire thread and have a question. If I am running 2200 mah 40-70C 2S with a 35a Turnigy water cooled ESC. With the given formula A=Ah x C
at 40 C I would be at 88a, and at 70C I would be at 156a. Depening on who you believe Turnigy max burst amps 150ish or Seaking max burst amps 70, am I heading for a melt down or is the water cooling making it workable.
#2352
Junior Member
Join Date: Oct 2010
Location: Portland, OR
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
I couldn't decide if I wanted to go small block or big block, so I did both. 2848 SL 3900KV Hobby Wing / Seaking (Big block) and 2040 SL 4800KV Hobbyking / Turnigy ( Small block). Even though I plan to run Nano tec 2200 2S, What do you think the motor / ESClongevity would be on 3S?
#2353
RE: Unofficial
28mm motor, no problem. That 2040 won't last long on 3S, but will do fine on 2S with a water jacket. The 28mm has enough torque to overcome the back-pressure at higher speeds and will be much faster.
#2354
Junior Member
Join Date: Oct 2010
Location: Portland, OR
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
The one thing that makes figuring out the power system is, unlike an airplane you dont have a Pitch andDia. to work into the calcs. I guess you do, but I dont know what it would be.
#2355
Member
Join Date: Mar 2009
Location: SydneyNSW, AUSTRALIA
Posts: 57
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
I got my little boat running... wow....... the 2040SL 4800kv moves... I think I have to turn down my end points to get a little bit more control over the RPM range.
I will put a video up later and picture.
Seeya James
I will put a video up later and picture.
Seeya James
#2356
Senior Member
Join Date: Mar 2005
Location: shellharbour, AUSTRALIA
Posts: 510
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
hi guys firstly i apologise for not reading the whole thread and working it out that way, so i hope you will take the time to help me.
im gonna build 2 of these for my 7 year old son and i. i would like to know your opinions on what is a good reliable setup. i would like to run 2s and just be able to chuck a batt in and hit the creek without having to spend alot of time fixing/repairing/rebuilding etc. as my rc surfer requires enough of that. ive got a heap of 2200 2s batts id like to use with it if possible.
so what do you think i should go with. ill probly get all the stuff from HK too. motor esc servo etc. im all set for tx rx
thanks in advance
mark
im gonna build 2 of these for my 7 year old son and i. i would like to know your opinions on what is a good reliable setup. i would like to run 2s and just be able to chuck a batt in and hit the creek without having to spend alot of time fixing/repairing/rebuilding etc. as my rc surfer requires enough of that. ive got a heap of 2200 2s batts id like to use with it if possible.
so what do you think i should go with. ill probly get all the stuff from HK too. motor esc servo etc. im all set for tx rx
thanks in advance
mark
#2357
Junior Member
Join Date: Jul 2011
Location: Halifax, NS, CANADA
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
Hi,
does anyone have a spare stator nozzle steering piece laying around? I've broken two now, I ended up snapping the top part of it off that holds the servo rod while taking them off.. I've tried gluing it back together but it's just not happening and I don't want it to fall apart whilst on the river. Anyways if someone could help me out that would be great. I'd pay for the part and shipping.
thanks,
-Nathan
does anyone have a spare stator nozzle steering piece laying around? I've broken two now, I ended up snapping the top part of it off that holds the servo rod while taking them off.. I've tried gluing it back together but it's just not happening and I don't want it to fall apart whilst on the river. Anyways if someone could help me out that would be great. I'd pay for the part and shipping.
thanks,
-Nathan
#2358
Member
Join Date: Feb 2008
Location: Townsville, AUSTRALIA
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
Nathen,
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
#2359
Join Date: Jan 2007
Location: PORTLAND, TN
Posts: 1,760
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
ORIGINAL: QIK-RX4
Nathen,
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
Nathen,
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
#2360
Junior Member
Join Date: Jul 2011
Location: Halifax, NS, CANADA
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
ORIGINAL: QIK-RX4
Nathen,
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
Nathen,
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
Those look great but like Dragonfire said it's for a different jet drive unit. I'd have to replace the whole thing and looks like the shaft is a different diameter as well so maybe not.
DragonFire, I'd really appreciate if you could bang me out a couple of those pieces. I'm considering going shopping for a permanent marker cap that I could manipulate to work for a temporary fix. What would you normally make the parts out of?
thanks,
-Nathan
#2361
RE: Unofficial
Nathan, if you get a stock replacement steering nozzle, the way to remove/install it is to pinch the sides together (it flexes) and it will get larger from top to bottom and will slip off easily.
#2362
Join Date: Jan 2007
Location: PORTLAND, TN
Posts: 1,760
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
ORIGINAL: murmuzy-tearinto
Those look great but like Dragonfire said it's for a different jet drive unit. I'd have to replace the whole thing and looks like the shaft is a different diameter as well so maybe not.
DragonFire, I'd really appreciate if you could bang me out a couple of those pieces. I'm considering going shopping for a permanent marker cap that I could manipulate to work for a temporary fix. What would you normally make the parts out of?
thanks,
-Nathan
ORIGINAL: QIK-RX4
Nathen,
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
Nathen,
This have the parts you need?
http://www.rcplanet.com/Pro_Boat_Dri..._p/prb3656.htm
Cheers,
Rob.
Those look great but like Dragonfire said it's for a different jet drive unit. I'd have to replace the whole thing and looks like the shaft is a different diameter as well so maybe not.
DragonFire, I'd really appreciate if you could bang me out a couple of those pieces. I'm considering going shopping for a permanent marker cap that I could manipulate to work for a temporary fix. What would you normally make the parts out of?
thanks,
-Nathan
#2363
Join Date: Jan 2007
Location: PORTLAND, TN
Posts: 1,760
Likes: 0
Received 0 Likes
on
0 Posts
#2365
Join Date: Jan 2007
Location: PORTLAND, TN
Posts: 1,760
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
im not really back . just lurking around . i did get my 1/8th buggy out the other day . and flow my plain and heli around . and i still havent even touched the 1/5 jet hull . but im starting to get the itch again .
#2366
Member
Join Date: Aug 2011
Location: Hobart TAS, AUSTRALIA
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
hi all, just a quicky, am finally putting together a parts list to order for the 2 boats im planning to mod and am wondering do i need to order a con-rod for my new servo's or is the stock one ok?also the rubber rod boot? not entirely sure as the nqd i bought was modded already (poorly)
http://www.hobbyking.com/hobbyking/s...dproduct=13401
had a whole heap of goodies in my shopping cart at hobbyking and kept going back and adding things i didnt really need because they looked good, then went back today and my cart had emptied itself with no way of knowing what i had in it! grrr, now i have to shop all over again
thanks
http://www.hobbyking.com/hobbyking/s...dproduct=13401
had a whole heap of goodies in my shopping cart at hobbyking and kept going back and adding things i didnt really need because they looked good, then went back today and my cart had emptied itself with no way of knowing what i had in it! grrr, now i have to shop all over again
thanks
#2369
RE: Unofficial
Yeah, Hobbyking just started doing that a couple months ago. You used to be able to 'hover' on a price and it would offer a better price after a few minutes, then you could put it in your cart for ordering later. But now you have to buy it that day or it will erase it. One way around that is to go back and find the cart in your history (mozilla firefox) and it will still be there with the good price.
#2370
Junior Member
Join Date: Jul 2011
Location: Halifax, NS, CANADA
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
That would be great. Yes all Ineed is a steering nozzle or two, I'd be interested in getting a couple of the smaller nozzles if you're willing to make a couple more. please let me know,
Thanks!
Thanks!
#2373
Junior Member
Join Date: Apr 2010
Location: , SWEDEN
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
Fun fun, I'm building a pick-up boat for my Tear Intos. Also waterjet of course, winch, crane, lights, radar and a peculiar ballast-system at the rear.
#2374
RE: Unofficial
I like the ballast! Pick up boat for the Tear Into? That sounds backwards! My Tear Into is possibly my most reliable boat and rarely has need for such, but it has been used to retrieve other boats before. Nice looking rig there.
#2375
Member
Join Date: Aug 2011
Location: Hobart TAS, AUSTRALIA
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
RE: Unofficial
thats exactly what happened sundogz, now all my once in a lifetime, never to be repeated, super dooper prices have disappeared! and i cant remember what i had finally decided on getting either! seems doing a system clean up and deleting temp internet files was the problem so tech help told me. thought it might have been saved on their servers not my pc?