JAE GAS Rigger video on YOUTUBE
#1
Junior Member
Thread Starter
Join Date: Dec 2006
Location: Huntsville,
AL
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
JAE GAS Rigger video on YOUTUBE
This video was taken Sat 3-13 during the test session in Huntsville...
The boat is the prototype JAE gas boat with a "box stock" RCMK rear exhaust motor....[the motor is turning 16,600 rpm]
The only smooth water was right in front of the drivers stand....this video does not do justice as to how rough the water was during this test run.
The new JAE gas boat does absolutely nothing stupid in any water conditions....
This run was with a Voodoo 7520 prop......We have several 3" plus diameter props coming to try and all indications are that 75mph
will be attainable with this JAE/"box stock" RCMK combo.....[we haven't even set the head clearance in this motor yet]
We have another gas boat prototype in construction and the same tests will be run with a "box stock" 260 Zenoah....
http://www.youtube.c...h?v=Oav0nqHRIhU
Note:Once again,the only adjustments required on this boat are prop selection,pipe length and needle valve....
The boat is the prototype JAE gas boat with a "box stock" RCMK rear exhaust motor....[the motor is turning 16,600 rpm]
The only smooth water was right in front of the drivers stand....this video does not do justice as to how rough the water was during this test run.
The new JAE gas boat does absolutely nothing stupid in any water conditions....
This run was with a Voodoo 7520 prop......We have several 3" plus diameter props coming to try and all indications are that 75mph
will be attainable with this JAE/"box stock" RCMK combo.....[we haven't even set the head clearance in this motor yet]
We have another gas boat prototype in construction and the same tests will be run with a "box stock" 260 Zenoah....
http://www.youtube.c...h?v=Oav0nqHRIhU
Note:Once again,the only adjustments required on this boat are prop selection,pipe length and needle valve....
#3
Senior Member
Join Date: Jul 2008
Location: Hialeah,
FL
Posts: 761
Likes: 0
Received 0 Likes
on
0 Posts
RE: JAE GAS Rigger video on YOUTUBE
I couldn't make it work for me either. Also looks like a duplicate post. He has the same post/link on the GF
http://www.rcuniverse.com/forum/fb.asp?m=9589223
http://www.rcuniverse.com/forum/fb.asp?m=9589223
#4
Senior Member
Join Date: Jan 2005
Location: blackpool, UNITED KINGDOM
Posts: 11,390
Likes: 0
Received 2 Likes
on
2 Posts
RE: JAE GAS Rigger video on YOUTUBE
Yea its allways a good idea to check your links after posting them ,cant find anything on utube either least not under gas JAE rigger .
Mart
Mart
#6
Senior Member
Join Date: Jan 2005
Location: blackpool, UNITED KINGDOM
Posts: 11,390
Likes: 0
Received 2 Likes
on
2 Posts
RE: JAE GAS Rigger video on YOUTUBE
ORIGINAL: noahdear
Googled it ... [link]http://www.youtube.com/watch?v=Oav0nqHRIhU[/link]
Googled it ... [link]http://www.youtube.com/watch?v=Oav0nqHRIhU[/link]
Mart
#8
Junior Member
Thread Starter
Join Date: Dec 2006
Location: Huntsville,
AL
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
RE: JAE GAS Rigger video on YOUTUBE
Yes the wind was blowwing ptretty hard at times. Plus rain and Hail too. Even had a radio glitch that sent the boat into the shore luckily it didn't hurt anything too bad.
#10
Junior Member
Thread Starter
Join Date: Dec 2006
Location: Huntsville,
AL
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
RE: JAE GAS Rigger video on YOUTUBE
I'm helping David Hall test his design bfore it goes to Joe for kitting that way we know the design is proven especially since we are using a stock RCMK engine tod the testing next one will be using a stock Zenoha so everyone will have a good comparison between the engines.