Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Page 17 of 17 FirstFirst ... 7151617
Results 401 to 415 of 415

  1. #401
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    Just the turn fin is rolled up. And my pride. it was kinda windy blowing from left to right. Way to windy for the .21 JAE ,I found my waterline pinched off completely no wonder she didn't go.
    that hull got some flying in. nothing damaged the hull is very light. That hull went as far as I've ever seen a hull fly. Like Rick said where did it go.
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  2. #402

    Join Date
    Jul 2007
    Location
    Atlantic Beach, FL
    Posts
    64
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    Ouch... bummer- beautiful hydro, loved the paintwork/trim color.
    Wes

  3. #403
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    Thanks Wes
    the hull ,I got 2 hand It's Chris Ripley old hull. He's the IMPBA president. The hull was made in D2 his name has gotten away from me. She did like to fly ,no damage to the hull. As you can see the turn fin angle picking the front of the hull up. My buddy said bring it back in to adjust the fin -sorry That fin may have bent & straighten before I got it. I made a new bracket and a old turn fin I have. That M&D Zenhoa is a beast.
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  4. #404
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    My 21 had a problem with not running after a launch. The engine didn't want to turn a H7 prop. I used a smaller prop from Cromby Zombie Wow I got a tank in Thanks Mark for the use. stubborn me The new to me .67 seducer did start- but my throttle linkage was sticking at the carb barrel. I do have a few CMB .67 carbs to mess with.The 67 SGX rigger ran perfect. minor needle adjustments when I get to Hamilton Ontario Canada
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  5. #405

    Join Date
    Feb 2008
    Location
    Canandaigua, NY
    Posts
    1,748
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go


    ORIGINAL: advanced builder

    My 21 had a problem with not running after a launch. The engine didn't want to turn a H7 prop. I used a smaller prop from Cromby Zombie Wow I got a tank in Thanks Mark for the use. stubborn me The new to me .67 seducer did start- but my throttle linkage was sticking at the carb barrel. I do have a few CMB .67 carbs to mess with.The 67 SGX rigger ran perfect. minor needle adjustments when I get to Hamilton Ontario Canada
    Sounds like a pretty good day! Smaller prop was a good move. I know my NR can have problems with some full blade 1450's if the needle is not perfect. Some engines are more torque and some are more RPM.... Either way you get the job done.
    Craig Mapstone, IMPBA #20305S, Stony Pond Model Boat Club
    2012 D1 20 Hydro Champion

  6. #406
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    We went over my engine as I'm still stalling out. I'm bringing out my old .21 green head CMB long stroke. to finish out the season.
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  7. #407

    Join Date
    Feb 2008
    Location
    Canandaigua, NY
    Posts
    1,748
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go


    ORIGINAL: advanced builder

    We went over my engine as I'm still stalling out. I'm bringing out my old .21 green head CMB long stroke. to finish out the season.
    The green head runs good. Too bad about the VAC.... []
    Craig Mapstone, IMPBA #20305S, Stony Pond Model Boat Club
    2012 D1 20 Hydro Champion

  8. #408
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    I 'm thinking the carb need a mod like removing the low speed needle. My green head has a Aeromarine racing carb. They have no small needle. Very basic carb same with that Orlic carb. I may seal the hole with JB weld and shape it to the radius. The green head was rebuilt with new bearings. 1-run on it to CK So I can beat the prof.
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  9. #409

    Join Date
    Feb 2008
    Location
    Canandaigua, NY
    Posts
    1,748
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    Yes, it would be nice to see a rigger win 20 hydro hi-points this year.....
    Craig Mapstone, IMPBA #20305S, Stony Pond Model Boat Club
    2012 D1 20 Hydro Champion

  10. #410
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    I will bring both .21 riggers with me, Friday to test.
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  11. #411
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: .21 Zippkit ready to go

    my old red hull may have run her last race. time to get my new hull running.
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  12. #412
    amax's Avatar
    Join Date
    Aug 2007
    Location
    Crawfordville, FL
    Posts
    927
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback
    I was Bored to Death at work so I started Playing Around with SolidWorks and Drew up this all Carbon Fiber JAE21G2 What Ya THink

    Click image for larger version. 

Name:	JAE21G2CF.JPG 
Views:	9 
Size:	1.24 MB 
ID:	1985540
    Top Speed Hobbies llc. Gotta Need For Speed..
    www.youtube.com/user/topspeedhobbies

  13. #413
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback
    nice looking rigger Amax, I'm not running a 21 JAE rigger this season, just too many hulls to run. I picked up a SGX 21 never ran her. Got 2 45 hulls to run a Blaze Marine Sport 40 and a Delta Force 40 Vee hull. i built them this winter. A few CF riggers are around my area not many. Terry Kleely has a CF topic on building a rigger in the IW build or rigger section.
    keep up the good work
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/

  14. #414
    amax's Avatar
    Join Date
    Aug 2007
    Location
    Crawfordville, FL
    Posts
    927
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback
    Yea thats just a 3D Model I put together in SolidWorks not the Real Thing YET!!!
    Top Speed Hobbies llc. Gotta Need For Speed..
    www.youtube.com/user/topspeedhobbies

  15. #415
    advanced builder's Avatar
    Join Date
    Feb 2006
    Location
    Baldwinsville, NY
    Posts
    3,017
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback
    Get rigger fever Amax
    Stoney Pond Model Boat Club, Canandaigua, NY
    International racer
    http://neilsrcsite.shutterfly.com/


Page 17 of 17 FirstFirst ... 7151617

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT -6. The time now is 11:28 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.