FOR SALE IS MY SERPENT COBRA GT -USED ON 3 TRACK DAYS ONLY AT A LOCAL TRACK 1 GALLON OF FUEL RAN THROUGH IT -COMES WITH A NEW BODY NOT YET CUT FOR NITRO WITH NO DAMAGE -HAS A NOVAROSSI ROMA 25 (BEST TORQUE AND RPM) -HAS A SAVOX 1256 TG STEERING SERVO -HAS A SAVOX 0352 ON THROTTLE -HAS A NOVAROSSI EFRA 9886 PIPE -IT IS SETUP FOR THE TRACK 300,000 FRNT AND CENTER DIFF AND REAR IS 40,000 -SHOCK OIL IS 1,000 -DOES NOT COME WITH RX,TX, RX BATTERY OR STARTER BOX -IT RUNS AND HANDLES GREAT ********************** -IF YOU HAVE ANY QUESTIONS CONTACT JOSE 305-910-7162 -SERIOUS QUESTIONS ONLY ********************** Serpent Cobra GT 1/8 4wd details
Chassisplate Chassisplate in 3mm 7075 T6 aluminium , with machined pockets to create flex and or make lighter. Kick-up angle on front as need due to the race-rules. Countersunk holes. Slots to locate the front and rear suspension mounts precisely. Angled sides to increase stiffness. Open pockets to access flywheel and 2-speed gearbox. Laser engraved Cobra GT logo.
Bumper Captured foam bumper set, with wide foam bumper and strong upper and lower bumper-plate.
Chassis stiffners Composite stiffner front and rear, to give extra stiffness, but still allow some flex as needed.
Central diskbrake system Very low and centrally placed brake system for low centre of gravity with ventilated glassfibre brake disks, combined with thick steel plates which wont bend under pressure.
Radio-box Composite radiobox which offers space for the lay-down steering servo and the upright placed brake-throttle servo. Sufficient spacers are supplied for correct fitting of the servo’s. The receiver and battery can be placed safely under the large cap. The transponder can be mounted in the central part, between servo and receiverbox. The whole assembly including linkages can be taken off easily and fast in one go, when cleaning the car, or doing maintenance.
Servo arms and linkages The servo arms have a splined insert to have the right fit per brand. The linkages runs very clean and tight and are easy to access to modify settings.
Suspension brackets Beautifully machined 7065 T6 suspension brackets in anodized, laser angraved. Pecision fit for the nylon roll center inserts and pivot balls / pins.
Steeringblocks assembly Composite steeringblocks combined with 10 dgr C-hubs for precise steering. Spring steel wheel-axles with large size bearings 8x18x5 and 15x21x4 with precision threaded aluminum wheel-hubs with +3 offset . Flanged and serrated wheel nuts to guarantee that you will not loose a wheel nut in a race.
Front suspension Durable oversized lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.
Front anti-roll bar The ballraced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the diff-cases and run in ballraced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction operation.
Shocktower and bodymounts front 4.5mm thick carbon shocktower with 5 upper positioning holes for the shocks and and 6 holes for roll-center positions. 1 centrally located adjustable bodymount , and 2 forward mounted adjustable bodymounts, all with flip-tops.
Angled steering system / servo saver The bell cranks are angled to reduce the angle of difference between the total caster and steering plane. Therefore you will have less bump steer and a truer steering Ackerman through the entire range of suspension
Ackerman plates With the design of the steering bell cranks when changing the Ackerman you will not need to adjust your steering tie rods. You simply will only need to adjust your end points on your radio..
Rear suspension arms Durable oversized lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.
Rear uprights assembly Composite uprights with 3 upper roll-center positions. Strong steel track-rods with L/R threading and strong balljoints to pre-set camber. Spring steel wheel-axles with large size bearings 8x16x5 and 13x19x4 with precision threaded aluminum wheel-hubs with +3 offset . Rubber dustcovers in the rear to protect the cvd system and kepe the lubrication inside. Flanged and serrated wheel nuts to guarantee that you will not loose a wheel nut in a race.
Rear anti-roll bar The ballraced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the diff-cases and runs in ballraced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction operation.
Shocktower rear 4.5mm thick carbon shocktower, integrated into the rear section for extra stiffness, with 5 upper positioning holes for the shocks and 6 holes for roll-center positions.
Wingmount and bodymounts rear Composite rear wing, with strong nylon adjustable rear bodymounts on wide body-support bridge located far enough to the rear, to support the bodies in best way. .
Captured pivot pins and balls and bolted hinge pins All spring-steel hinge pins are either captured or bolted in place and made in spring-steel quality. This insures your chances to finish an hour long main event, while battling for the lead. This relieves stress on the hinge pin when adjusting the kick up, or anti squat. Your pin is free to rotate to any angle without binding.
Shockabsorbers big-bore 16mm Hard Teflon coated threaded shockbodies with 4mm shock-rods. Black anodized aluminium screw on shock-tops with Serpent laser engraving. Pre-load adjusters with o-rings inside. Shocks use large diameter membrames and large diameter o-rings and bushings to create a supersmooth and leak-proof package. Large diameter pistons are held in place by a nut on the polished shock-rods tops. Open type spring retainer to let dirt out easy.
RCM shock springs Short type colorcoded shock springs are supplied for the 1st standard set-up Springs are grinded flat top and bottom, and checked individually for tension and length.
Compact geardifferentials Very compact gear differentials with very smooth metal sintered gears, and steel shaft. Perfect sealing case with special gasket and o-rings. Very light and durable outdrive cups in spring-steel. Hardened spring-steel diff-coupler 13T with connector running in 2 oversized bearings 8x19x6 and ballbearing-13x19x4.
Front and rear cvd-sets Both front and rear captured driveshafts are being used with CVD system. Durable yet light spring steel engraved driveshafts with hard steel pins.
Spring steel transmission parts The front and rear thin but strong spring steel cardan shafts connect the differentials with the gearbox section.
Engine mount Machined 7075 T6 aluminium engine mounts with side cooling fins.
Coil exhaust wire and alu mount The tuned pipe is securely fastened with the cols spring and alumium holder. Helps aid in the front to back movement of the pipe when chassis flex occurs. Helps to prevent damage to your exhaust gaskets.
SL8 2-speed gearbox SL8 gearbox comes straight from the Serpent 966 1/8 scale onroad car. Very light and compact design. Centrifugal spring loaded shoe system with large alu bell and flange with one-way bearing. Durable composite 2-speed gears.
2-speed clutch-housing with screw-on gears Strong steel clutch-housing with precision machined threading, with hard coated aluminum screw on gears.
4-shoe clutch Full carbon 4 shoe clutch-set with medium type springs. Easy to assemble with light and durable anodized aluminum flywheel.
150cc fueltank Composite nyon fuel-tank with supersealing springloaded shock-cap, bronze sintered clunk type filter and splash-side guard. Side features slots to mount the supplied tube-guiders. Tank mounts to chassis on longer composite posts with integrated rubber buffers to allow some movement and reduce fuel-foaming. The clunk system will allow the engine to continue running when the car is up-side-down.
Oils and grease The shock-oil, diff oil and some grease is supplied to meet the standard set-up.
Manual and set-up Full color manual with easy to follow assembly steps, exploded views for easy spares ordering, a blank and standard set-up sheet for a good start set-up.
Decals Black and white promo body-decals ; Serpent generic and Cobra GT ones.
Packing Parts are packed according to the steps explained in the manual.
Service and Support The Serpent distributor, dealer or agent is your source for more info, but also the Serpent website and the member section and the Youtube channel provides lots of information.