Notices
"1/2 A" & "1/8 A" airplanes These are the small ones...more popular now than ever.

Long Live LaStick!

Old 07-05-2017, 11:45 AM
  #1  
Tee Bee
Thread Starter
 
Join Date: Feb 2007
Location: Angleton, TX
Posts: 1,984
Received 3 Likes on 3 Posts
Default Long Live LaStick!

So, back in 2007, I built a LaStick, Fred Reese's modern version of the Little Stick from plans I found on this 1/2A site. It was my 2nd RC plane build. I powered it with an awesome little Cox TD .010 engine and flew it for several years like that. It flew just fine but I eventually wanted MORE from the model. More speed and longer flight times. When I finally sourced a TD .020 at a good price, I upgraded the plane by modifying the firewall for the larger engine, switching from covering material hinges to stronger hinges cut from a mylar floppy disk and CA'd in place. To keep it balanced, I switched from a NiCad battery to a lighter NiMH with more capacity. The new makeover really woke up the performance and made the airplane much more thrilling to fly. It has been flown a lot at every SMALL event I've attended. In 2015, several of us had different versions of little Sticks with TD .020s there and we had a blast flying them around the pattern together, burning thru tank after tank, making that awesome noise. At this year's SMALL, several of the local club flyers at the event spent the weekend playing with their FPV quadcopters, zooming up and down the flightline, sometimes hovering over the runway while airplanes made their passes, landings, etc. As luck would have it, my little 10yr old plane hit one of them. It sliced right thru the balsa wing and returned to land with no damage while my poor LaStick went down in the tall chigger grass. Luckily, other than a destroyed wing, the airframe was intact and the engine survived with only a broken carb body. After I returned home from Arkansas, I was able to purchase a couple of reproduction carb bodies from MECOA. I think they are made from the original Cox castings, and unlike the more durable aluminum carbs that are available, they have the little stub that anchors the starter spring. I tore the little engine down to clean out the dirt, reset the piston, and replaced the old hardened fuel line with some new stuff from Cox International. With that sorted, I printed out some new LaStick plans from Outerzone and set out to cut ribs and build a new wing. This one is a touch stronger and a little sleeker than before with a slightly smaller airfoil and a bit less dihedral. I deviated a bit from the traditional Maltese cross graphics to finish the facelift. This morning, I took her out to my club field for some test flying. I was very pleased, as the engine ran like a top and the plane was faster and flew better than ever. After 6 fun-filled flights, I cleaned her up, oiled the engine, and hung her back up in the traditional spot above my computer desk where I'm typing this. Life is good!
Attached Thumbnails Click image for larger version

Name:	IMG_3896[1].JPG
Views:	84
Size:	105.6 KB
ID:	2223096   Click image for larger version

Name:	IMG_3913[1].JPG
Views:	77
Size:	2.08 MB
ID:	2223097   Click image for larger version

Name:	IMG_3935[1].JPG
Views:	65
Size:	2.11 MB
ID:	2223098   Click image for larger version

Name:	IMG_3991[1].JPG
Views:	65
Size:	2.19 MB
ID:	2223099   Click image for larger version

Name:	IMG_3996[1].JPG
Views:	65
Size:	2.44 MB
ID:	2223100   Click image for larger version

Name:	IMG_3998[1].JPG
Views:	66
Size:	2.70 MB
ID:	2223101   Click image for larger version

Name:	IMG_4046[1].JPG
Views:	70
Size:	3.05 MB
ID:	2223102   Click image for larger version

Name:	IMG_4047[1].JPG
Views:	89
Size:	3.23 MB
ID:	2223103  

Click image for larger version

Name:	IMG_4048[1].JPG
Views:	85
Size:	2.05 MB
ID:	2223104  
The following users liked this post:
brickwoodward (02-02-2022)
Old 07-05-2017, 05:30 PM
  #2  
LittleRock
 
Join Date: Oct 2004
Location: Little Rock, AR
Posts: 207
Likes: 0
Received 1 Like on 1 Post
Default

Don't I owe you $100.00 ???
The following users liked this post:
brickwoodward (02-02-2022)
Old 07-05-2017, 05:55 PM
  #3  
Tee Bee
Thread Starter
 
Join Date: Feb 2007
Location: Angleton, TX
Posts: 1,984
Received 3 Likes on 3 Posts
Default

Naw. To be fare, the drone landed with no damage....this time.
The following users liked this post:
brickwoodward (02-02-2022)
Old 07-05-2017, 07:40 PM
  #4  
Andrew
 
Join Date: Feb 2003
Location: Murray, KY
Posts: 3,213
Received 3 Likes on 3 Posts
Default

That was a great story of life, death and rebirth!!! Super graphics, BTW.
The following users liked this post:
brickwoodward (02-02-2022)
Old 07-05-2017, 08:06 PM
  #5  
Tee Bee
Thread Starter
 
Join Date: Feb 2007
Location: Angleton, TX
Posts: 1,984
Received 3 Likes on 3 Posts
Default

Thanks. I came home from SMALL with a renewed enthusiasm for the little planes. Besides repairing this model, I've been restoring some old crusty Cox engines of various styles and sizes to proper working order and prepping to build some new planes to put them on.
The following users liked this post:
brickwoodward (02-02-2022)
Old 07-08-2017, 12:35 AM
  #6  
BrightGarden
 
BrightGarden's Avatar
 
Join Date: Jun 2014
Location: Hudson Valley. New York. USA
Posts: 283
Likes: 0
Received 2 Likes on 2 Posts
Default

Great story, no plane or engine left behind...
The following users liked this post:
brickwoodward (02-02-2022)

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.