|
CAP 3D 25 Size 1100 mm
Dear All,
Could anobody help me. I am intrested in find some information about this plane. I live in Hungary and I asked experianced hungarian modellers but nobody can help me. Some of them have a CAP 232 but in a biger size. If somebody could write me some experiance about the building process or flying performance please don't hesitate ;) I have this kit and it looks like very nice. If somebody have a movie about the Cap 3d flying please send me it an email to [email protected]. Thanks for your help Good night from a snowy Hungary [8D] Zoli |
RE: CAP 3D 25 Size 1100 mm
1 Attachment(s)
Here is the picture if somebody don't heard anything about Baby Cap:
|
RE: CAP 3D 25 Size 1100 mm
Pls Help ME [&o]
|
RE: CAP 3D 25 Size 1100 mm
Dear alll,
Pls help me!!! I am still searching for any information on the websites but I cannot find anything. Please give me the link or an adress where I can see something about this type of ARF. The another name of the plane is BABY CAP. It is a china modell product. Please if you have the video about this plane send to [email protected] or give me the link. ;) THANKS THANKS THANKS :( Zoltán |
RE: CAP 3D 25 Size 1100 mm
i had this model before and it flies extremely well. the finishing is of good quality but you know that since you already have the kit!
my set up was as follows: O.S. 32SX enough for unlimited vertical APC 9x6 prop JETI RX 5 HS-81 Micro Servos 4.8V AAA RX pack it flew very well and take offs and landings were really non events. 3D performance isn't great since it's short fuse needs bigger elevators and rudder (or a lot more pilot skill!) but it's aerobatics were fun. it's truly a sunday flyer with a little attitude. the only thing i did different was not put on all the graphics and put some white monokote on the wings so that they don't disappear on final approach (against a green/brown hill). i lost the plane due to low RX batteries. basically i was out for the last trip of the day. i had charged my pack that day and despite after flying all afternoon, i figured i still had some juice left. on the dive approach of a high speed, low pass the radio froze and it went in at about 60 degrees at three quarters throttle. i would buy that plane again and have been seriously thinking about it since i've now purchased some 40 fourstrokes. |
RE: CAP 3D 25 Size 1100 mm
ORIGINAL: forestroke i had this model before and it flies extremely well. the finishing is of good quality but you know that since you already have the kit! my set up was as follows: O.S. 32SX enough for unlimited vertical APC 9x6 prop JETI RX 5 HS-81 Micro Servos 4.8V AAA RX pack it flew very well and take offs and landings were really non events. 3D performance isn't great since it's short fuse needs bigger elevators and rudder (or a lot more pilot skill!) but it's aerobatics were fun. it's truly a sunday flyer with a little attitude. the only thing i did different was not put on all the graphics and put some white monokote on the wings so that they don't disappear on final approach (against a green/brown hill). i lost the plane due to low RX batteries. basically i was out for the last trip of the day. i had charged my pack that day and despite after flying all afternoon, i figured i still had some juice left. on the dive approach of a high speed, low pass the radio froze and it went in at about 60 degrees at three quarters throttle. i would buy that plane again and have been seriously thinking about it since i've now purchased some 40 fourstrokes. |
RE: CAP 3D 25 Size 1100 mm
i never weighed it. but it was light. if you're thinking electric, i think it's a very good candidate.
|
RE: CAP 3D 25 Size 1100 mm
I cant afford to think electic in anything bigger than a foamy. I think it would make a nice flier with my .28 glow.
|
RE: CAP 3D 25 Size 1100 mm
hmmm... the 28, huh? well it may not have unlimited verticals then. i remember during the vert test that the 32SX would pull out of my hands but hardly enough for one of those stonking pull outs. i think the 28 would still be great for all around acrobatic fun but would not be enough to really do any 3D.
32SX on 15% Omega |
RE: CAP 3D 25 Size 1100 mm
What about a Magnum 36 on 15 % omega
|
| All times are GMT -8. The time now is 06:40 AM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.