Tonymura

I everyone. Nice to meet you all.
My very first post here and lets hope i have placed this in the right area so here we go.
Ok i need some advice probably this might not be the best place to ask this question in the beginner section so lets hope i get this right.
i am planning to build an electric surfboard.
Just wanting to know as few things from the community on what would be the best brushless dc motor including the ESC to look at for my water jet thruster that i am in the process of building / molding.
The size of the impeller should be about 70mm so i am seeking someone opinion to whats readily available out there.
Any suggestions would be very much appreciated.
If i have placed this post in the wrong area could the moderators please redirect me or move my thread if possible to the correct area.so that i can continue asking more question with my project to the appropriate community team member's.
Any advice would be very much appreciated.
Thank you all in advance.

Hydro Junkie

That's more information than you gave me in the PMs you sent. I also didn't like your last response as your level of impatience was, to say the least, obvious. That said, you can ignore the reply I gave you as I'm out

Tonymura

So quick to reply after i asked you as very simple question as to why your are so interested in my personal life in regards to what English i speak or where i come from.
All i asked is what section do i post my first thread. A simple request. Nothing more nothing less
I was never rude to you but you where rude to me asking me and demanding me 4 things. These four things dont include what English i speak if i ask advice on what electric motor i need for my project.
So quick and smart you art to post here on the community in your defense.
This make you now look quiet silly.
I find you blatant disrespectful nature to not assist me in a simple request rather than asking my personal life.
Your out.....really fine by me..... I will wait for another user who can talk to me like decent human being. Your to smart for me...my back luck, so unfortunate i wont be sharing you knowledge.
Good day to you.

Hydro Junkie

You may not think you were rude, I sure the hell did. You got on me about taking too long to give you information after you answered my questions. You asked me to help you put electric power with R/C control on a surf board, no information or anything else. I asked questions to try to figure out what you actually wanted and where you were located so I could try to find sources LOCAL FOR YOU and, less than 12 hours later, you started complaining about me not responding after you answered my questions. Then, less than a minute later, I see you started a thread in the forum asking the same question but with considerably more information than you gave me to go on. I'm sorry, that is nothing more than rude, in my opinion. As I said, you're on your own and I won't be responding to you again. If anyone else thinks I'm wrong, they can send me a PM and I'll discuss it with them there. I have my own boats to build or repair and others to help with their projects here in the forum

Tonymura

All i asked you was where should i start my first post.
I dont need your help. I can ask other users.
I just dont like you asking as you have done in other post to other users your demands to 4 questions that dont relate to my project building.
You had no intentions to write back to me. I just started on my own here this my first thread. I never invited you here to this post, you invited yourself after reading my pm .
Now what your doing is posting it here to all users to .......what....make me look bad....
Look at your post counts and look at mine.....who do you think moderators would side on. of course you. So i have to be careful here or i'll be out...for sure
Your being rude again....you should have wrote to me in a personal massage rather than trying to degrade me right here to....what.... try and make you look good.
I never invited you here on this thread.
You never had any intentions to reply back to me did you.
Judging by your comments in the PM you wrote that we dont all speak the same English those we are not all the same.....
What does that mean.....sounds very racist to me....
I told you i am from Australia......you could have just said look your really not part of this world, so i will decline my assistance to you rather than you write so sarcastically towards me or just not correspond with me at all and we could have left it there and then.
You can just said bugger off bro. I dont like your kind.
So what are you doing to me right now, Are you out to get brownie point here to all other users.

Would you like me to copy and paste the private message of what i wrote to you HERE so other users can read carefully on how this all started
and now your telling me your OUT....really.....
if your telling me your OUT then why are you still writing to me right here on my post..

Thats fine i dont need your advice........I wont be begging for it....
I am just a new forum patron here, starting out, on my own,......... i dont like to be treated like this....this is what i call internet bullying to those who are from another country.
I apologies if i am not from the US, and haven't meet your expectations.

If other users are reading all of THIS....I would like to say sorry ...how embarrassing what a...mess.....this is not the way i behave.

If other users have any ideas on a brushless motor please post me here with some advice to get off this topic...

In regards to you Hydro or what ever your name is......listen mate......us Aussies dont act like this, this is not the way we treat other human beings or behave, please try and get some manner s and mate.... on a final note please dont post here on my thread again Your comments are not welcome..

Hopefully my English was good enough to understand.

jester_s1

Since the entirety of this thread is a personal pissing contest between two grown men, I'm shutting it down. This doesn't belong in the airplane forum anyway.