CMP F6F HellCat 120 - 71" Scale Nitro
#1
Junior Member
Thread Starter
Join Date: Feb 2007
Location: kuna, ID
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
CMP F6F HellCat 120 - 71" Scale Nitro
I was lokking at the CMP F6F HellCat 120 - 71" Scale Nitro thought I would get some oppinions on this plane good or bad
#3
My Feedback: (5)
Join Date: Jan 2002
Location: Lake Havasu City,
AZ
Posts: 521
Likes: 0
Received 0 Likes
on
0 Posts
RE: CMP F6F HellCat 120 - 71" Scale Nitro
You may find something of interest here:
http://www.rcuniverse.com/forum/m_25..._1/key_/tm.htm
http://www.rcuniverse.com/forum/m_25..._1/key_/tm.htm
#5
Member
Join Date: Jul 2006
Location: wyckoff,
NJ
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
RE: CMP F6F HellCat 120 - 71
Guys- I have the CMP Hellcat and ZERO. A 6-7 year hiatus kept me from touching the kits. I can't find any leads on placing in many nice add-ons...like steerable tail wheel ( more scale than the wire the kit provides) and I have the Sierra custom retracts: beautiful workmanship. I finally have the wings ready to 1/4 glass and the retract gear installation is the only holdup on that. HehI'm open for input!!...Ed Sarkisian.....I'm BACK!!
#6
Member
Join Date: Jul 2006
Location: wyckoff,
NJ
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
RE: CMP F6F HellCat 120 - 71
Guys- just learning the roes again on this RC univ threading....trying to not get caught up in a spiderweb of communication, to get some build- up ideas on basic structure for the CMP hellcat. My dad and I also have the CMP zero-my Dad is original crew Of THE AIRCRAFT CARRIER USS YORKTOWN, CV-10 anti - aircraft gunner. I AM SO BLESSED TO HAVE HIM, guys... And need some streamlined info on getting this Hellcat going
We have the OS1.20 everyone suggested years back
-we have the custom retracts.
I know how to pint, detail and weather the aircraft.
on My left ring finger is my wedding ring///on MY RIGHT RING FINGER IS THE RING MY DAD MADE OF THE TAILHOOK FROM ONE OF THE USS YORKTOWNS HELLCATS.
I'm looking for help guys,,,,
Hints on the engine mounting/ prop ( three bladed !! )
Thank you- Edward A Sarkisian [email protected]
We have the OS1.20 everyone suggested years back
-we have the custom retracts.
I know how to pint, detail and weather the aircraft.
on My left ring finger is my wedding ring///on MY RIGHT RING FINGER IS THE RING MY DAD MADE OF THE TAILHOOK FROM ONE OF THE USS YORKTOWNS HELLCATS.
I'm looking for help guys,,,,
Hints on the engine mounting/ prop ( three bladed !! )
Thank you- Edward A Sarkisian [email protected]
#7
Junior Member
Join Date: Jan 2013
Location: Malta, MALTA
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
RE: CMP F6F HellCat 120 - 71
HI!
I have a CMP HellCat 120 size, and bought a RCG20cc engine for it.. Now the problem is here.. I dont know where to pass with the throttle push rod ! since the carb is set at the back and where the arm is set its in the position where the fuel tank sits inside the plane! PLEASE HELP!!!!
YOu could reply here or email ; [email protected]
I have a CMP HellCat 120 size, and bought a RCG20cc engine for it.. Now the problem is here.. I dont know where to pass with the throttle push rod ! since the carb is set at the back and where the arm is set its in the position where the fuel tank sits inside the plane! PLEASE HELP!!!!
YOu could reply here or email ; [email protected]