Go Back  RCU Forums > RC Helicopters > Electric RC Helis > E-Flite Helicopters
Reload this Page >

Gyro Blade450 settings well off?

Notices
E-Flite Helicopters Discuss the line of E-Flite mini and micro helis including the Blade CP, CP Pro, Blade CX, etc

Gyro Blade450 settings well off?

Old 03-30-2012, 01:26 AM
  #1  
denodan
Member
Thread Starter
 
Join Date: Feb 2012
Location: ChristchurchNot Applicable, NEW ZEALAND
Posts: 92
Likes: 0
Received 0 Likes on 0 Posts
Default Gyro Blade450 settings well off?

I got the BNF version of the Blade 450, copied the intermedite settings listed in the manual, but found the standard Gyro setting is well off the mark, get tail wag at those settings, which is 77.5%, dropped it down to 65%, even 60% and no tail wag.

How can they get their settings so wrong? Or do all the copters very? Also seen some videos of the Blade 450 and they have also used Gyro setting of 60-65%


Old 03-30-2012, 06:09 AM
  #2  
donkey doctor
Senior Member
 
Join Date: Nov 2002
Location: Lake Cowichan, BC, CANADA
Posts: 1,341
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Gyro Blade450 settings well off?

Hello; I'm still looking for the right set-up for my recently acquired 450
blade. As close as I can come seems to tear off the ground and immediately roll right.
I realize that it might be better that I do all the expensive crashing on the flight simulator


I've seen Blade 450's flown in a controlled way, but mine doesn't go that way.
Old 03-30-2012, 09:01 AM
  #3  
denodan
Member
Thread Starter
 
Join Date: Feb 2012
Location: ChristchurchNot Applicable, NEW ZEALAND
Posts: 92
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Gyro Blade450 settings well off?

I put all thje settrings that came with the Bllade manual and work fine. The only thing that was off was the Gyro setting listed.
Old 03-30-2012, 09:10 AM
  #4  
evdreamer
 
Join Date: Aug 2007
Location: Lincoln, NE
Posts: 6,430
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Gyro Blade450 settings well off?

Gyro settings vary with tail rotor speed, tail blades, gyros, and transmitters. You can increase the resolution of the tail servo by moving the pushrod ball closer to the center of the servo wheel. Doing that will allow you to increase your gain. If the gain you have now is working stick with it and don't worry too much about what E-flite recommends. Finless bob on Helifreak has some great videos about setting up gyros.
Old 09-10-2012, 10:57 AM
  #5  
turko
Junior Member
 
Join Date: Jan 2010
Location: vancouver, BC, CANADA
Posts: 6
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Gyro Blade450 settings well off?

Gyro settings depend on how far from center you have your tail servo set. It is suppose to be 7-9 mmls from center.I had mine at 12 mmls and gyro gain was 62% any higher and I got wag. I reset the servo link to *mmls this morning and now have 77.5% gain with no wag.
Old 09-10-2012, 10:59 AM
  #6  
turko
Junior Member
 
Join Date: Jan 2010
Location: vancouver, BC, CANADA
Posts: 6
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Gyro Blade450 settings well off?

The length is 8 mmls.

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.